PCF8574RGYRG4 datasheet(5/36 Pages) TI1

5 / 36 page

PCF8574

www.ti.com

SCPS068I – JULY 2001 – REVISED NOVEMBER 2015

6.5 Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

VCC

MIN TYP(1)

MAX

UNIT

VIK

Input diode clamp voltage

II = –18 mA

2.5 V to 6 V

–1.2

VPOR

Power-on reset voltage(2)

VI = VCC or GND,

IO = 0

6 V

1.3

2.4

IOH

P port

VO = GND

2.5 V to 6 V

300

μA

IOHT

P port transient pullup current

High during acknowledge, VOH = GND

2.5 V

–1

SDA

VO = 0.4 V

2.5 V to 6 V

IOL

P port

VO = 1 V

5 V

INT

VO = 0.4 V

2.5 V to 6 V

1.6

SCL, SDA

±5

INT

VI = VCC or GND

2.5 V to 6 V

±5

μA

A0, A1, A2

±5

IIHL

P port

VI ≥ VCC or VI ≤ GND

2.5 V to 6 V

±400

μA

Operating mode

VI = VCC or GND,

IO = 0,

fSCL = 100 kHz

100

ICC

6 V

μA

Standby mode

VI = VCC or GND,

IO = 0

2.5

SCL

VI = VCC or GND

2.5 V to 6 V

1.5

SDA

Cio

VIO = VCC or GND

2.5 V to 6 V

P port

(1)

All typical values are at VCC = 5 V, TA = 25°C.

(2)

The power-on reset circuit resets the I2C-bus logic with VCC < VPOR and sets all I/Os to logic high (with current source to VCC).

6.6 I

2C Interface Timing Requirements

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 12)

MIN

MAX

UNIT

fscl

I2C clock frequency

100

kHz

tsch

I2C clock high time

μs

tscl

I2C clock low time

4.7

μs

tsp

I2C spike time

100

tsds

I2C serial data setup time

250

tsdh

I2C serial data hold time

ticr

I2C input rise time

μs

ticf

I2C input fall time

0.3

μs

tocf

I2C output fall time (10-pF to 400-pF bus)

300

tbuf

I2C bus free time between stop and start

4.7

μs

tsts

I2C start or repeated start condition setup

4.7

μs

tsth

I2C start or repeated start condition hold

μs

tsps

I2C stop condition setup

μs

tvd

Valid data time

SCL low to SDA output valid

3.4

μs

I2C bus capacitive load

400

6.7 Switching Characteristics

over recommended operating free-air temperature range, CL ≤ 100 pF (unless otherwise noted) (see Figure 13)

FROM

PARAMETER

MIN

MAX

UNIT

(INPUT)

(OUTPUT)

tpv

Output data valid

SCL

P port

μs

tsu

Input data setup time

P port

SCL

μs

Input data hold time

P port

SCL

μs

tiv

Interrupt valid time

P port

INT

μs

tir

Interrupt reset delay time

SCL

INT

μs

Submit Documentation Feedback

Product Folder Links: PCF8574

PCF8574RGYRG4 数据表(PDF) 5 Page - Texas Instruments

PCF8574RGYRG4 数据表(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载

链接网址

PCF8574RGYRG4 数据表(PDF) 5 Page - Texas Instruments

PCF8574RGYRG4 数据表(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表 下载

链接网址

数据表下载