数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

HYS64T64020HDL 数据表(PDF) 14 Page - Infineon Technologies AG

部件名 HYS64T64020HDL
功能描述  200-Pin Small Outline Dual-In-Line Memory Module
PDF  48 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  INFINEON [Infineon Technologies AG]
网页  http://www.infineon.com
标志 INFINEON - Infineon Technologies AG

HYS64T64020HDL 数据表(HTML) 14 Page - Infineon Technologies AG

Back Button HYS64T64020HDL Datasheet HTML 10Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 11Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 12Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 13Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 14Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 15Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 16Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 17Page - Infineon Technologies AG HYS64T64020HDL Datasheet HTML 18Page - Infineon Technologies AG Next Button
Zoom Inzoom in Zoom Outzoom out
 14 / 48 page
background image
HYS64T[32000/64020/128021][G/H]DL–[3.7/5]–A
512 Mbit DDR2 SDRAM
Overview
Data Sheet
14
Rev. 0.91, 2004-06
09122003-FTXN-KM26
Table 8
Input/Output Functional Description
Symbol
Type
Polarity
Function
CK[1:0],
CK[1:0]
I
Cross
point
The system clock inputs. All address and command lines are sampled on the
cross point of the rising edge of CK and the falling edge of CK. A Delay Locked
Loop (DLL) circuit is driven from the clock inputs and output timing for read
operations is synchronized to the input clock.
CKE[1:0]
I
Active
High
Activates the DDR2 SDRAM CK signal when high and deactivates the CK signal
when low. By deactivating the clocks, CKE low initiates the Power Down Mode
or the Self Refresh Mode.
S[1:0]
I
Active
Low
Enables the associated DDR2 SDRAM command decoder when low and
disables the command decoder when high. When the command decoder is
disabled, new commands are ignored but previous operations continue. Rank 0
is selected by S0; Rank 1 is selected by S1.
RAS, CAS,
WE
IActive
Low
When sampled at the cross point of the rising edge of CK,and falling edge of CK,
RAS, CAS and WE define the operation to be executed by the SDRAM.
BA[1:0]
I
—
Selects internal SDRAM memory bank
ODT[1:0]
I
Active
High
Asserts on-die termination for DQ, DM, DQS, and DQS signals if enabled via the
DDR2 SDRAM mode register.
A[9:0],
A10/AP,
A[13:11]
I
—
During a Bank Activate command cycle, defines the row address when sampled
at the crosspoint of the rising edge of CK and falling edge of CK. During a Read
or Write command cycle, defines the column address when sampled at the cross
point of the rising edge of CK and falling edge of CK. In addition to the column
address, AP is used to invoke autoprecharge operation at the end of the burst
read or write cycle. If AP is high, autoprecharge is selected and BA0-BAn
defines the bank to be precharged. If AP is low, autoprecharge is disabled.
During a Precharge command cycle, AP is used in conjunction with BA[1:0] to
control which bank(s) to precharge. If AP is high, all banks will be precharged
regardless of the state of BA[1:0] inputs. If AP is low, then BA[1:0] are used to
define which bank to precharge.
DQ[63:0]
I/O
—
Data Input/Output pins
DM[7:0]
I
Active
High
The data write masks, associated with one data byte. In Write mode, DM
operates as a byte mask by allowing input data to be written if it is low but blocks
the write operation if it is high. In Read mode, DM lines have no effect.
DQS[7:0],
DQS[7:0]
I/O
Cross
point
The data strobes, associated with one data byte, sourced with data transfers. In
Write mode, the data strobe is sourced by the controller and is centered in the
data window. In Read mode the data strobe is sourced by the DDR2 SDRAM
and is sent at the leading edge of the data window. DQS signals are
complements, and timing is relative to the crosspoint of respective DQS and
DQS. If the module is to be operated in single ended strobe mode, all DQS
signals must be tied on the system board to
V
SS through a 20 ohm to 10 Kohm
resistor and DDR2 SDRAM mode registers programmed appropriately.
V
DD,
V
DDSPD, VSS
Supply
—
Power supplies for core, I/O, Serial Presence Detect, and ground for the module.
SDA
I/O
—
This is a bidirectional pin used to transfer data into or out of the SPD EEPROM.
A resistor must be connected from SDA to
V
DDSPD on the motherboard to act as
a pull-up.
SCL
I
—
This signal is used to clock data into and out of the SPD EEPROM.
SA[1:0]
I
—
Address pins used to select the Serial Presence Detect base address.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com