SP3243ECT datasheet(10/24 Pages) SIPEX

10 / 24 page

Rev. 11/14/02

SP3223E +3.0V to +5.5V RS-232 Transceivers

DESCRIPTION

The SP3223E and SP3243E transceivers meet

the EIA/TIA-232 and ITU-T V.28/V.24 commu-

nication protocols and can be implemented in

battery-powered, portable, or hand-held appli-

cations such as notebook or palmtop computers.

The SP3223E and SP3243E devices feature

Sipex's proprietary and patented (U.S.--

5,306,954) on-board charge pump circuitry that

generates

±5.5V RS-232 voltage levels from a

single +3.0V to +5.5V power supply. The

SP3223E and SP3243E devices can operate at

a typical data rate of 235kbps fully loaded.

The SP3223E is a 2-driver/2-receiver device,

and the SP3243E is a 3-driver/5-receiver device

ideal for portable or hand-held applications.

The SP3243E includes one complementary

always-active receiver that can monitor an

external device (such as a modem) in shutdown.

This aids in protecting the UART or serial

controller IC by preventing forward biasing

of the protection diodes where V

CC may be

disconnected.

The SP3223E and SP3243E series is an ideal

choice for power sensitive designs. The SP3223E

and SP3243E devices feature AUTO ON-LINE®

circuitry which reduces the power supply drain

to a 1

µA supply current. In many portable or

hand-held applications, an RS-232 cable can be

disconnected or a connected peripheral can be

turned off. Under these conditions, the internal

charge pump and the drivers will be shut down.

Otherwise, the system automatically comes

online. This feature allows design engineers to

address power saving concerns without major

design changes.

THEORY OF OPERATION

The SP3223E and SP3243E series is made up

of four basic circuit blocks:

1. Drivers, 2. Receivers, 3. the Sipex proprietary

charge pump, and 4. AUTO ON-LINE® cir-

cuitry.

Drivers

The drivers are inverting level transmitters that

convert TTL or CMOS logic levels to 5.0V EIA/

TIA-232 levels with an inverted sense relative to

the input logic levels. Typically, the RS-232

output voltage swing is +5.4V with no load and

+5V minimum fully loaded. The driver outputs

are protected against infinite short-circuits to

ground without degradation in reliability. These

drivers comply with the EIA-TIA-232F and all

previous RS-232 versions. Unused driver inputs

should be connected to GND or V

CC.

The drivers can guarantee a data rate of 120Kbps

fully loaded with 3K

Ω in parallel with 1000pF,

ensuring compatibility with PC-to-PC commu-

nication software.

The slew rate of the driver output is internally

limited to a maximum of 30V/

µs in order to

meet the EIA standards (EIA RS-232D 2.1.7,

Paragraph 5).

The transition of the loaded

output from HIGH to LOW also meets the

monotonicity requirements of the standard.

Figure 11. Interface Circuitry Controlled by Micropro-

cessor Supervisory Circuit

SP3243E

5KΩ

GND

C1+

C1-

C2+

C2-

V+

V-

VCC

0.1µF

RS-232

OUTPUTS

RS-232

INPUTS

VCC

1IN

1OUT

1IN

2OUT

2IN

3IN

3OUT

1OUT

2IN

3IN

4IN

5IN

2OUT

3OUT

4OUT

5OUT

ONLINE

SHUTDOWN

STATUS

UART

Serial µC

µP

Supervisor

TxD

RTS

DTR

RxD

CTS

DSR

DCD

VCC

VIN

RESET

SP3243ECT 数据表(PDF) 10 Page - Sipex Corporation

SP3243ECT 数据表(HTML) 10 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载