PIC16F877AISLASHML datasheet(107/234 Pages) MICROCHIP

107 / 234 page

 2003 Microchip Technology Inc.

DS39582B-page 105

PIC16F87XA

9.4.14

SLEEP OPERATION

While in Sleep mode, the I2C module can receive

addresses or data and when an address match or com-

plete byte transfer occurs, wake the processor from

Sleep (if the MSSP interrupt is enabled).

9.4.15

EFFECT OF A RESET

A Reset disables the MSSP module and terminates the

current transfer.

9.4.16

MULTI-MASTER MODE

In Multi-Master mode, the interrupt generation on the

detection of the Start and Stop conditions allows the

determination of when the bus is free. The Stop (P) and

Start (S) bits are cleared from a Reset or when the

MSSP module is disabled. Control of the I2C bus may

be taken when the P bit (SSPSTAT<4>) is set, or the

bus is Idle, with both the S and P bits clear. When the

bus is busy, enabling the SSP interrupt will generate

the interrupt when the Stop condition occurs.

In multi-master operation, the SDA line must be

monitored for arbitration to see if the signal level is at

the expected output level. This check is performed in

hardware with the result placed in the BCLIF bit.

The states where arbitration can be lost are:

• Address Transfer

• Data Transfer

• A Start Condition

• A Repeated Start Condition

• An Acknowledge Condition

9.4.17

MULTI -MASTER COMMUNICATION,

BUS COLLISION AND BUS

ARBITRATION

Multi-Master mode support is achieved by bus arbitra-

tion. When the master outputs address/data bits onto

the SDA pin, arbitration takes place when the master

outputs a ‘1’ on SDA by letting SDA float high and

another master asserts a ‘0’. When the SCL pin floats

high, data should be stable. If the expected data on

SDA is a ‘1’ and the data sampled on the SDA pin = 0,

then a bus collision has taken place. The master will set

the Bus Collision Interrupt Flag, BCLIF, and reset the

I2C port to its Idle state (Figure 9-25).

If a transmit was in progress when the bus collision

occurred, the transmission is halted, the BF flag is

cleared, the SDA and SCL lines are deasserted and the

SSPBUF can be written to. When the user services the

bus collision Interrupt Service Routine and if the I2C

bus is free, the user can resume communication by

asserting a Start condition.

If a Start, Repeated Start, Stop or Acknowledge condition

was in progress when the bus collision occurred, the con-

dition is aborted, the SDA and SCL lines are deasserted

and the respective control bits in the SSPCON2 register

are cleared. When the user services the bus collision

Interrupt Service Routine and if the I2C bus is free, the

user can resume communication by asserting a Start

condition.

The Master will continue to monitor the SDA and SCL

pins. If a Stop condition occurs, the SSPIF bit will be set.

A write to the SSPBUF will start the transmission of

data at the first data bit regardless of where the

transmitter left off when the bus collision occurred.

In Multi-Master mode, the interrupt generation on the

detection of Start and Stop conditions allows the determi-

nation of when the bus is free. Control of the I2C bus can

be taken when the P bit is set in the SSPSTAT register or

the bus is Idle and the S and P bits are cleared.

FIGURE 9-25:

BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE

SDA

SCL

BCLIF

SDA released

SDA line pulled low

by another source

Sample SDA. While SCL is high,

data doesn’t match what is driven

Set bus collision

interrupt (BCLIF)

by the master. Bus collision has occurred.

by master

Data changes

while SCL = 0

PIC16F877AI/ML 数据表(PDF) 107 Page - Microchip Technology

PIC16F877AI/ML 数据表(HTML) 107 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载