 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
PCM56UG4 数据表(PDF) 2 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
PCM56UG4 数据表(HTML) 2 Page - Texas Instruments |
|
|
2 / 16 page  2 ® PCM56 DIGITAL INPUT Resolution 16 Bits Digital Inputs(1): VIH +2.4 +VL V VIL 0 +0.8 V IIH, VIN = +2.7V +1.0 µA IIL, VIN = +0.4V –50 µA Input Clock Frequency 10.0 MHz TRANSFER CHARACTERISTICS ACCURACY Gain Error ±2.0 % Bipolar Zero Error ±30 mV Differential Linearity Error ±0.001 % of FSR(2) Noise (rms, 20Hz to 20kHz) at Bipolar Zero (VOUT models) 6 µV TOTAL HARMONIC DISTORTION VO = ±FS at f = 991Hz: PCM56P-K –94 –92 dB PCM56P-J –94 –88 dB PCM56P, PCM56U –94 –82 dB PCM56P-L –94 –80 dB VO = –20dB at f = 991Hz: PCM56P-K –75 –74 dB PCM56P-J –75 –68 dB PCM56P, PCM56U –75 –68 dB PCM56P-L –75 –60 dB VO = –60dB at f = 991Hz: PCM56P-K –35 –34 dB PCM56P-J –35 –28 dB PCM56P, PCM56U –35 –28 dB PCM56P-L –35 –20 dB MONOTONICITY 15 Bits DRIFT (0 °C to +70°C) Total Drift(3) ±25 ppm of FSR/ °C Bipolar Zero Drift ±4 ppm of FSR/ °C SETTLING TIME (to ±0.006% of FSR) Voltage Output: 6V Step 1.5 µs 1LSB 1.0 µs Slew Rate 10 V/ µs Current Output, 1mA Step: 10 Ω to 100Ω Load 350 ns 1k Ω Load(4) 350 ns WARM-UP TIME 1Min OUTPUT Voltage Output Configuration: Bipolar Range ±3.0 V Output Current ±2.0 mA Output Impedance 0.10 Ω Short Circuit Duration Current Output Configuration: Bipolar Range ( ±30%) ±1.0 mA Output Impedance ( ±30%) 1.2 k Ω POWER SUPPLY REQUIREMENTS(5) Voltage: +VS and +VL +4.75 +5.00 +13.2 V –VS and –VL –4.75 –5.00 –13.2 V Supply Drain (No Load): +V (+VS and +VL = +5V) +10.00 +17.0 mA –V (–VS and –VL = –5V) –25.0 –35.0 mA +V (+VS and +VL = +12V) +12.0 mA –V (–VS and –VL = –12V) –27.0 mA Power Dissipation: VS and VL = ±5V 175 260 mW VS and VL = ±12V 468 mW TEMPERATURE RANGE Specification 0 +70 °C Operation –25 +70 °C Storage –60 +100 °C NOTES: (1) Logic input levels are TTL/CMOS-compatible. (2) FSR means full-scale range and is equivalent to 6V ( ±3V) for PCM56 in the V OUT mode. (3) This is the combined drift error due to gain, offset, and linearity over temperature. (4) Measured with an active clamp to provide a low impedance for approximately 200ns. (5) All specifications assume +VS connected to +VL and –VS connected to –VL. If supplies are connected separately, –VL must not be more negative than –VS supply voltage to assure proper operation. No similar restriction applies to the value of +VL with respect to +VS. PCM56U, PCM56P-J, -K PARAMETER MIN TYP MAX UNITS SPECIFICATIONS ELECTRICAL Typical at +25 °C, and nominal power supply voltages ±5V, unless otherwise noted. Indefinite to Common |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
