13

LP5900

www.ti.com

SNVS358R – JULY 2005 – REVISED JUNE 2016

Product Folder Links: LP5900

Submit Documentation Feedback

Copyright © 2005–2016, Texas Instruments Incorporated

(1)

The actual power dissipation across the device can be represented by Equation 2:

(2)

This establishes the relationship between the power dissipation allowed due to thermal consideration, the voltage

drop across the device, and the continuous current capability of the device. These two equations should be used

to determine the optimum operating conditions for the device in the application.

8.2.2.2 External Capacitors

Like any low-dropout regulator, the LP5900 requires external capacitors for regulator stability. The LP5900 is

specifically designed for portable applications requiring minimum board space and smallest components. These

capacitors must be correctly selected for good performance.

8.2.2.2.1

Input Capacitor

An input capacitor is required for stability. The input capacitor should be at least equal to or greater than the

output capacitor. It is recommended that a 0.47-µF capacitor be connected between the LP5900 IN pin and

ground.

This capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean

analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.

Important: To ensure stable operation it is essential that good PCB practices are employed to minimize ground

impedance and keep input inductance low. If these conditions cannot be met, or if long leads are to be used to

connect the battery or other power source to the LP5900, then it is recommended to increase the input capacitor

to at least 2.2 µF. Also, tantalum capacitors can suffer catastrophic failures due to surge current when connected

to a low-impedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at

the input, it must be ensured by the manufacturer to have a surge current rating sufficient for the application.

There are no requirements for the equivalent series resistance (ESR) on the input capacitor, but tolerance and

temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain

0.47

μF ±30% over the entire operating temperature range.

8.2.2.2.2

Output Capacitor

The LP5900 is designed specifically to work with very small ceramic output capacitors. A ceramic capacitor

(dielectric types X5R or X7R) in the 0.47

μF to 10 μF range, and with ESR between 5 mΩ to 500 mΩ, is suitable

in the LP5900 application circuit. For this device the output capacitor should be connected between the OUT pin

and a good ground connection and should be mounted within 1 cm of the device.

It may also be possible to use tantalum or film capacitors at the device output, OUT, but these are not as

attractive for reasons of size and cost (see the Capacitor Characteristics section below).

The output capacitor must meet the requirement for the minimum value of capacitance and have an ESR value

that is within the range 5 m

Ω to 500 mΩ for stability.

8.2.2.2.3

Capacitor Characteristics

The LP5900 is designed to work with ceramic capacitors on the input and output to take advantage of the

benefits they offer. For capacitance values in the range of 0.47

μF to 4.7 μF, ceramic capacitors are the smallest,

least expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise.

The ESR of a typical 0.47-

μF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the

equivalent series resistance (ESR) requirement for stability for the LP5900.

The temperature performance of ceramic capacitors varies by type and manufacturer. Most large value ceramic

capacitors (

≥ 2.2 µF) are manufactured with Z5U or Y5V temperature characteristics, which results in the

capacitance dropping by more than 50% as the temperature goes from 25°C to 85°C.

A better choice for temperature coefficient in a ceramic capacitor is X7R. This type of capacitor is the most stable

and holds the capacitance within ±15% over the temperature range. Tantalum capacitors are less desirable than

ceramic for use as output capacitors because they are more expensive when comparing equivalent capacitance

and voltage ratings in the 0.47

μF to 4.7 μF range.