| 数据搜索系统,热门电子元器件搜索 |
|
DS485 数据表(PDF) 3 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
DS485 数据表(HTML) 3 Page - National Semiconductor (TI) |
|
3 / 10 page ![]() Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified (Notes 3, 7, 8) Symbol Parameter Conditions Min Typ Max Units t PLHD Driver Differential Propagation Delay — Low to High R L = 54Ω,CL = 100 pF 10 40 65 ns t PHLD Driver Differential Propagation Delay — High to Low 10 39 65 ns t SKEW Differential Skew |t PHLD −tPLHD| 1 10 ns t r Driver Rise Time 325 40 ns t f Driver Fall Time 325 40 ns t ZH Driver Enable to Output High C L = 100 pF 170 ns t ZL Driver Enable to Output Low C L = 100 pF 170 ns t LZ Driver Disable from Output Low C L = 15 pF 170 ns t HZ Driver Disable from Output High C L = 15 pF 170 ns t PLHD Receiver Differential Propagation Delay — Low to High C L = 15 pF (RO) 70 190 320 ns t PHLD Receiver Differential Propagation Delay — High to Low 70 210 320 ns t SKEW Differential Skew |t PHLD −tPLHD|20 50 ns t ZH Receiver Enable to Output High C L = 15 pF 110 ns t ZL Receiver Enable to Output Low 110 ns t LZ Receiver Disable from Output Low 110 ns t HZ Receiver Disable from Output High 110 ns f max Maximum Data Rate (Note 9) 2.5 Mbps Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD1/2/3 and VID. Note 3: All typicals are given for: VCC = +5.0V, TA = +25˚C. Note 4: ∆|VOD| and ∆|VOC| are changes in magnitude of V OD and VOCrespectively, that occur when the input changes state. Note 5: IIN2 includes the receiver input current and driver TRI-STATE leakage current. Note 6: Supply current specification is valid for loaded transmitters when DE = 0V or enabled (DE = H) with no load. Note 7: f = 1 MHz, tr and tf ≤ 6 ns, ZO = 50Ω. Note 8: CL includes jig and probe capacitance. Note 9: fmax is the guaranteed data rate for 50 ft of twisted pair cable. f max may be conservatively determined from the ratio of driver transition time (tr) to the data rate unit interval (1/fmax). Using a 10% ratio yields fmax = (0.1)/40 ns = 2.5 Mb/s. Higher data rates may be supported by allowing larger ratios. www.national.com 3 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |