4.0 Absolute Maximum Ratings for

the LM111/LM211(Note 10)

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Total Supply Voltage (V

36V

Output to Negative Supply Voltage

(V

50V

Ground to Negative Supply Voltage

(V

30V

Differential Input Voltage

Input Voltage (Note 4)

Output Short Circuit Duration

10 sec

Operating Temperature Range

LM111

−55˚C to 125˚C

LM211

−25˚C to 85˚C

Lead Temperature (Soldering, 10 sec)

260˚C

Voltage at Strobe Pin

V

Soldering Information

Dual-In-Line Package

Soldering (10 seconds)

260˚C

Small Outline Package

Vapor Phase (60 seconds)

215˚C

Infrared (15 seconds)

220˚C

See AN-450 “Surface Mounting Methods and Their Effect

on Product Reliability” for other methods of soldering

surface mount devices.

ESD Rating (Note 11)

300V

Electrical Characteristics (Note 6) for the LM111 and LM211

Parameter

Conditions

Min

Typ

Max

Units

Input Offset Voltage (Note 7)

T

≤50k

0.7

3.0

mV

Input Offset Current

T

4.0

10

nA

Input Bias Current

T

60

100

nA

Voltage Gain

T

40

200

V/mV

Response Time (Note 8)

T

200

ns

Saturation Voltage

V

IN

≤−5 mV, I

0.75

1.5

V

T

Strobe ON Current (Note 9)

T

2.0

5.0

mA

Output Leakage Current

V

IN

≥5 mV, V

0.2

10

nA

T

Input Offset Voltage (Note 7)

R

S

≤50 k

4.0

mV

Input Offset Current (Note 7)

20

nA

Input Bias Current

150

nA

Input Voltage Range

V

−14.5

13.8,-14.7

13.0

V

Pull-Up May Go To 5V

Saturation Voltage

V

+

0.23

0.4

V

V

IN

≤−6 mV, I

OUT

≤8mA

Output Leakage Current

V

IN

≥5 mV, V

0.1

0.5

µA

Positive Supply Current

T

5.1

6.0

mA

Negative Supply Current

T

4.1

5.0

mA

negative supply voltage or 30V below the positive supply, whichever is less.

Note 5: The maximum junction temperature of the LM111 is 150˚C, while that of the LM211 is 110˚C. For operating at elevated temperatures, devices in the H08

package must be derated based on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line

package is 110˚C/W, junction to ambient.

temperature specifications are limited to −25˚C

Note 7: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply witha1mA load. Thus, these

Note 8: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.

Note 9: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe pin

to ground; it should be current driven at 3 to 5 mA.

Note 10: Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.

Note 11: Human body model, 1.5 k

Ω in series with 100 pF.

www.national.com

3