COP8SGC528M3 datasheet(49/62 Pages) NSC

49 / 62 page

14.0 Instruction Set (Continued)

Reg/

Contents

Memory

Before

After

Location

32 Hex

0126 Hex

The VIS instruction is a special case of the Indirect Transfer

of Control addressing mode, where the double-byte vector

associated with the interrupt is transferred from adjacent

addresses in program memory into the Program Counter in

order to jump to the associated interrupt service routine.

14.4 INSTRUCTION TYPES

The instruction set contains a wide variety of instructions.

The available instructions are listed below, organized into

related groups.

Some instructions test a condition and skip the next instruc-

tion if the condition is not true. Skipped instructions are

executed as no-operation (NOP) instructions.

14.4.1 Arithmetic Instructions

The arithmetic instructions perform binary arithmetic such as

addition and subtraction, with or without the Carry bit.

Add (ADD)

Add with Carry (ADC)

Subtract (SUB)

Subtract with Carry (SUBC)

Increment (INC)

Decrement (DEC)

Decimal Correct (DCOR)

Clear Accumulator (CLR)

Set Carry (SC)

Reset Carry (RC)

14.4.2 Transfer-of-Control Instructions

The transfer-of-control instructions change the usual se-

quential program flow by altering the contents of the Pro-

gram Counter. The Jump to Subroutine instructions save the

Program Counter contents on the stack before jumping; the

Return instructions pop the top of the stack back into the

Program Counter.

Jump Relative (JP)

Jump Absolute (JMP)

Jump Absolute Long (JMPL)

Jump Indirect (JID)

Jump to Subroutine (JSR)

Jump to Subroutine Long (JSRL)

Return from Subroutine (RET)

Return from Subroutine and Skip (RETSK)

Return from Interrupt (RETI)

Software Trap Interrupt (INTR)

Vector Interrupt Select (VIS)

14.4.3 Load and Exchange Instructions

The load and exchange instructions write byte values in

registers or memory. The addressing mode determines the

source of the data.

Load (LD)

Load Accumulator Indirect (LAID)

Exchange (X)

14.4.4 Logical Instructions

The logical instructions perform the operations AND, OR,

and XOR (Exclusive OR). Other logical operations can be

performed by combining these basic operations. For ex-

ample, complementing is accomplished by exclusiveORing

the Accumulator with FF Hex.

Logical AND (AND)

Logical OR (OR)

Exclusive OR (XOR)

14.4.5 Accumulator Bit Manipulation Instructions

The Accumulator bit manipulation instructions allow the user

to shift the Accumulator bits and to swap its two nibbles.

Rotate Right Through Carry (RRC)

Rotate Left Through Carry (RLC)

Swap Nibbles of Accumulator (SWAP)

14.4.6 Stack Control Instructions

Push Data onto Stack (PUSH)

Pop Data off of Stack (POP)

14.4.7 Memory Bit Manipulation Instructions

The memory bit manipulation instructions allow the user to

set and reset individual bits in memory.

Set Bit (SBIT)

Reset Bit (RBIT)

Reset Pending Bit (RPND)

14.4.8 Conditional Instructions

The conditional instruction test a condition. If the condition is

true, the next instruction is executed in the normal manner; if

the condition is false, the next instruction is skipped.

If Equal (IFEQ)

If Not Equal (IFNE)

If Greater Than (IFGT)

If Carry (IFC)

If Not Carry (IFNC)

If Bit (IFBIT)

If B Pointer Not Equal (IFBNE)

And Skip if Zero (ANDSZ)

Decrement Register and Skip if Zero (DRSZ)

14.4.9 No-Operation Instruction

The no-operation instruction does nothing, except to occupy

space in the program memory and time in execution.

No-Operation (NOP)

Note: The VIS is a special case of the Indirect Transfer of Control addressing

mode, where the double byte vector associated with the interrupt is

transferred from adjacent addresses in the program memory into the

program counter (PC) in order to jump to the associated interrupt

service routine.

COP8SGC528M3 数据表(PDF) 49 Page - National Semiconductor (TI)

COP8SGC528M3 数据表(HTML) 49 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

数据表下载