RN42 datasheet(13/26 Pages) MICROCHIP

13 / 26 page

 2015 Microchip Technology Inc.

DS50002328A-page 13

RN42/RN42N

3.1.2

RF EXPOSURE

All transmitters regulated by FCC must comply with RF

exposure requirements. KDB 447498 General RF

Exposure Guidance provides guidance in determining

whether proposed or existing transmitting facilities,

operations or devices comply with limits for human

exposure to Radio Frequency (RF) fields adopted by

the Federal Communications Commission (FCC).

From the FCC Grant: Power Output listed is conducted.

This module must be installed by the OEM or OEM inte-

grator. Instructions on installation of this module may

not be provided to the end user. The antenna used for

this transmitter must not be co-located with any other

transmitters except in accordance with FCC multi-

transmitter product. procedures. Installers must be pro-

vided with antenna installation instructions for satisfy-

ing RF exposure compliance. Installers and end users

must be provided with transmitter operating conditions

for satisfying RF exposure compliance.

3.1.3

HELPFUL WEB SITES

Federal Communications Commission (FCC): http://

www.fcc.gov

FCC Office of Engineering and Technology (OET) Lab-

oratory Division Knowledge Database (KDB): http://

apps.fcc.gov/oetcf/kdb/index.cfm

3.2

Canada

The RN42 module has been certified for use in Canada

under Industry Canada (IC) Radio Standards Specifica-

tion (RSS) RSS-210 and RSSGen. Modular approval

permits the installation of a module in a host device

without the need to recertify the device.

3.2.1

LABELING AND USER

INFORMATION REQUIREMENTS

Labeling Requirements for the Host Device (from Sec-

tion 3.2.1, RSS-Gen, Issue 3, December 2010): The

host device shall be properly labeled to identify the

module within the host device.

The Industry Canada certification label of a module

shall be clearly visible at all times when installed in the

host device, otherwise the host device must be labeled

to display the Industry Canada certification number of

the module, preceded by the words “Contains transmit-

ter module”, or the word “Contains”, or similar wording

expressing the same meaning, as follows:

User Manual Notice for License-Exempt Radio Appara-

tus (from Section 7.1.3 RSS-Gen, Issue 3, December

2010): User manuals for license-exempt radio appara-

tus shall contain the following or equivalent notice in a

conspicuous location in the user manual or alterna-

tively on the device or both:

Transmitter Antenna (from Section 7.1.2 RSS-Gen,

Issue 3, December 2010): User manuals for transmit-

ters shall display the following notice in a conspicuous

location:

The above notice may be affixed to the device instead

of displayed in the user manual.

3.2.2

RF EXPOSURE

All transmitters regulated by IC must comply with RF

exposure requirements listed in RSS-102 - Radio Fre-

quency (RF) Exposure Compliance of Radiocommuni-

cation Apparatus (All Frequency Bands).

3.2.3

HELPFUL WEB SITES

Industry Canada: http://www.ic.gc.ca

RN42:

Contains transmitter module IC: 6514A-RN42

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Indus-

trie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux con-

ditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit

accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le

fonctionnement.

Under Industry Canada regulations, this radio trans-

mitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the trans-

mitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotrop-

ically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Conformément à la réglementation d'Industrie Can-

ada, le présent émetteur radio peut fonctionner avec

une antenne d'un type et d'un gain maximal (ou

inférieur) approuvé pour l'émetteur par Industrie Can-

ada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il

faut choisir le type d'antenne et son gain de sorte

que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à

l'établissement d'une communication satisfaisante.

RN42 数据表(PDF) 13 Page - Microchip Technology

RN42 数据表(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

数据表下载