Environmental Specifications

Operating temperature

-20 °C to 50 °C ambient, derate each output as 2.5% per degree from 50 °C to 70 °C;

-40 °C startup if Standby output ≤ 1A (any valid load on main output);

-30 °C startup if Standby output > 1A (any valid load on main output)

Storage temperature

-40 °C to +85 °C

Electromagnetic susceptibility

Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3

Humidity

Operating; non-condensing 10% to 95% RH

Vibration

IEC68-2-6 to the levels of IEC721-3-2

MTBF calculated

>2 million hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore

Ordering Information

Model

Number

Output

Voltage

Minimum

Load

Maximum Load with

Convection Cooling

Maximum Load

with Forced Air

Peak

Load

Ripple

LPS363-M

12 V

0 A

20 A

30 A

39 A

±2%

120 mV

LPS364-M

15 V

0 A

16 A

24 A

31 A

±2%

150 mV

LPS365-M

24 V

0 A

10 A

15 A

19.5 A

±2%

240 mV

LPS366-M

36 V

0 A

14.62 A

±2%

360 mV

LPS368-M

48 V

0 A

5 A

7.5 A

9.75 A

±2%

480 mV

1. Peak current lasting <3 seconds.

2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.

3. Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.

4. LPS366-M is limited to the lower of the applicable power rating or current rating, whichever results in lowest power.

5. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate

standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users.

Pin Assignments

Connector

LPS360-M

J4

Pin 1

Line

Pin 3

Neutral

Barr

Barr-1

Main output +

Barr-2

Main output common

J5

Pin 1

+V1 Remote sense

Pin 2

-V1 Remote sense

Pin 3

+5 V Standby

Pin 4

5 V Standby return

Pin 5

+Power fail

Forced air operation

Pin 7

Inhibit

Pin 8

GND

Pin 9

SDA

Pin 10

SCL

J3

Pin 1

+12 V Fan

Pin 2

12 V fan Return (isolated)

** For forced air operation, connect pin 6 to pin 8 of J5.

Mating Connectors

J4 AC Input

Molex 09-50-3031 (connector)

PINS: 08-52-0072

J6 AC Ground

Molex 01-90020001

DC Output

(Barr)

Molex 19141-0058/0063 or 19099/0048

Spade lug based on Cable Ampacity/AWG

J5 Control Signals

Molex 90142-0010 (USA)

PINS: 90119-2110

J3 Fan Output

Molex 51065-0200

Pins: 50212-8100

The Artesyn Connector Kit #70-841-029, includes all of the above.

1. Specifications subject to change without notice.

2. All dimensions in inches (mm), tolerance is ±0.02”(±0.5 mm)

3. Mounting holes MH1 and MH2 should be grounded for EMI purposes.

4. Mounting hole MH1 is safety ground connection.

5. Specifications are for convection rating at factory settings at 115 VAC input, 25 °C unless

otherwise stated.

6. This power supply requires mounting on metal standoffs 0.20” (5m) in height.

7. Warranty: 3 Years

8. Weight: 0.4kg / 0.88 lb (LPS363-M)

LPS360-M Series Data Sheet

73-769-001

73-841-030

Artesyn Connector Kit #73-769-005 includes both of the above