Installations Instructions

PST24 Rev. 01

Page 7 of 8

www.powersystemtechnology.com

These converters are components, intended exclusively for integration into

other equipment by an industrial assembly process or by a professionnaly

competent person. Installation must strictly follow the safety regulations

in respect of the enclosure, mounting, creepage and clearance distances,

markings of the end-use application.

Connection to the system shall be made via the corresponding mating

connector .

The +IN is internally fused. This fuse is designed to protect the converter against

overcurrent caused by a failure, but may not be able to satisfy all requirements.

External fuses in the wiring circuit to one or both input pins may be necessary

to ensure compliance with local requirements.

Do not open the converters, or the warranty will be invalidated. Make sure that

there is sufficient heat dissipation available for conduction cooling. This should

be verified by measuring the case of temperature at the specified measuring

point, when the converter is operated in the end-use application.

Cleaning Agents and Process

The converters are not hermetically sealed. In order to avoid possible damage,

any penetration of liquids shall be avoided.

Isolation

The electric strength test is performed in the factory in accordance with IEC/EN

60950.

Standards and Approvals

The converters are built to meet the safety standards IEC 60950-1, EN 60950-1,

UL 60950-1 and CSA 60950-1.

Connector Pin Allocation

INPUT : J1: Molex 90130-3212 ( 12pins, 3A / pin ), J3: Molex 90130-3206 (6 pins)

ĀȀ̀

ЀԀ؀܀ࠀऀ਀଀ऀఀഀ

ĀȀ̀ЀԀЀ؀܀ЀȀࠀ

ऀ਀଀

ఀ܀ഀ฀؀฀ༀကЀ฀ᄀሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀ

ĀȀ̀ЀȀЀ؀܀Ѐᜀ

᠀਀଀

଀ကᘀᔀ؀฀ༀကЀ฀ᄀሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀ

ĀȀ̀ЀᤀЀ؀܀Ѐᨀ

ᬀᔀᰀ؀ᴀ

Āࠀ̀Ȁ

ऀḀἀ

ఀ܀ഀ฀؀฀ༀကЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀἀ

Āࠀ̀ЀࠀЀ؀܀Ѐ!Ѐ

"ḀȀ

#က؀ጀᰀᄀЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀȀ

Āࠀ̀Ѐ$Ѐ؀܀ЀȀᤀЀ

ऀḀȀ

ఀ܀ഀ฀؀฀ༀကЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀȀ

Āࠀ̀ЀȀ!Ѐ؀܀Ѐࠀ"Ѐ

"ḀȀ

#က؀ጀᰀᄀЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀȀ

Āࠀ̀ࠀȀЀ؀܀Ѐࠀᤀ

ऀḀࠀ

ఀ܀ഀ฀؀฀ༀကЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀࠀ

Āࠀ̀Ѐࠀ!Ѐ؀܀Ѐἀ"Ѐ

"Ḁࠀ

#က؀ጀᰀᄀЀ ጀ؀ሀጀ؀Ѐༀ܀᐀؀ᔀᘀကЀࠀ

ĀἂȀ

᠀਀଀%

᠀Ѐ਀ᄀᴀ฀&฀؀฀܀ᄀЀ

Āἂࠀ

ऀ਀଀%

ऀЀ਀ᄀᴀ฀&฀؀฀܀ᄀЀ

Safety and Installations Instructions

OUTPUT : J2: Molex 90130-3230 ( 30 pins, 3A / pin )