AM5718AABCX datasheet(11/394 Pages) TI1

11 / 394 page

AM5718, AM5716

www.ti.com

SPRS957C – MARCH 2016 – REVISED NOVEMBER 2016

Submit Documentation Feedback

Terminal Configuration and Functions

NOTE

In some cases Table 4-2 may present more than one signal name per muxmode for the

same

ball.

First

signal

the

list

the

dominant

function

selected

via

CTRL_CORE_PAD_* register.

All other signals are virtual functions that present alternate multiplexing options. This virtual

functions

are

controlled

via

CTRL_CORE_ALT_SELECT_MUX

CTRL_CORE_VIP_MUX_SELECT register. For more information on how to use this options,

please refer to Device TRM, Chapter Control Module, Section Pad Configuration Registers.

4. PN: This column shows if the functionality is applicable for AM5716 device. Note that the Ball

Characteristics table presents a functionality of AM5718. If the cell is empty it means that the signal is

available in all devices.

- Yes - Functionality is presented in AM5716

- No - Functionality is not presented in AM5716

An empty box means Yes.

5. MUXMODE: Multiplexing mode number:

(a) MUXMODE 0 is the primary mode; this means that when MUXMODE=0 is set, the function

mapped on the pin corresponds to the name of the pin. The primary muxmode is not necessarily

the default muxmode.

NOTE

The default mode is the mode at the release of the reset; also see the RESET REL.

MUXMODE column.

(b) MUXMODE 1 through 15 are possible muxmodes for alternate functions. On each pin, some

muxmodes are effectively used for alternate functions, while some muxmodes are not used. Only

MUXMODE values which correspond to defined functions should be used.

6. TYPE: Signal type and direction:

–

I = Input

–

O = Output

–

IO = Input or Output

–

D = Open drain

–

DS = Differential Signaling

–

A = Analog

–

PWR = Power

–

GND = Ground

–

CAP = LDO Capacitor

7. BALL RESET STATE: The state of the terminal at power-on reset:

–

drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated).

–

drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated).

–

OFF: High-impedance

–

PD: High-impedance with an active pulldown resistor

–

PU: High-impedance with an active pullup resistor

8. BALL RESET REL. STATE: The state of the terminal at the deactivation of the rstoutn signal (also

mapped to the PRCM SYS_WARM_OUT_RST signal).

–

drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated).

–

drive clk (OFF): The buffer drives a toggling clock (pulldown or pullup resistor not activated).

–

drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated).

–

OFF: High-impedance

–

PD: High-impedance with an active pulldown resistor

–

PU: High-impedance with an active pullup resistor

AM5718AABCX 数据表(PDF) 11 Page - Texas Instruments

AM5718AABCX 数据表(HTML) 11 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载