AM29F200 datasheet(12/39 Pages) AMD

12 / 39 page

Am29F200B

gramming, which might otherwise be caused by

spurious system level signals during VCC power-up and

power-down transitions, or from system noise.

Low VCC Write Inhibit

When VCC is less than VLKO, the device does not

accept any write cycles. This protects data during VCC

power-up and power-down. The command register and

all internal program/erase circuits are disabled, and the

device resets. Subsequent writes are ignored until VCC

is greater than VLKO. The system must provide the

proper signals to the control pins to prevent uninten-

tional writes when VCC is greater than VLKO.

Write Pulse “Glitch” Protection

Noise pulses of less than 5 ns (typical) on OE#, CE# or

WE# do not initiate a write cycle.

Logical Inhibit

Write cycles are inhibited by holding any one of OE# =

VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,

CE# and WE# must be a logical zero while OE# is a

logical one.

Power-Up Write Inhibit

If WE# = CE# = VIL and OE# = VIH during power up, the

device does not accept commands on the rising edge

of WE#. The internal state machine is automatically

reset to reading array data on power-up.

COMMAND DEFINITIONS

Writing specific address and data commands or

sequences into the command register initiates device

operations. The Command Definitions table defines the

valid register command sequences. Writing incorrect

address and data values or writing them in the

improper sequence resets the device to reading array

data.

All addresses are latched on the falling edge of WE# or

CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens

first. Refer to the appropriate timing diagrams in the

“AC Characteristics” section.

Reading Array Data

The device is automatically set to reading array data

after device power-up. No commands are required to

retrieve data. The device is also ready to read array

data after completing an Embedded Program or

Embedded Erase algorithm.

After the device accepts an Erase Suspend command,

the device enters the Erase Suspend mode. The

system can read array data using the standard read

timings, except that if it reads at an address within

erase-suspended sectors, the device outputs status

data. After completing a programming operation in the

Erase Suspend mode, the system may once again

read array data with the same exception. See “Erase

Suspend/Erase Resume Commands” for more infor-

mation on this mode.

The system must issue the reset command to re-

enable the device for reading array data if DQ5 goes

high, or while in the autoselect mode. See the “Reset

Command” section, next.

See also “Requirements for Reading Array Data” in the

“Device Bus Operations” section for more information.

The Read Operations table provides the read parame-

ters, and Read Operation Timings diagram shows the

timing diagram.

Reset Command

Writing the reset command to the device resets the

device to reading array data. Address bits are don’t

care for this command.

The reset command may be written between the

sequence cycles in an erase command sequence

before erasing begins. This resets the device to reading

array data. Once erasure begins, however, the device

ignores rese t commands until the op eration is

complete.

The reset command may be written between the

sequence cycles in a program command sequence

before programming begins. This resets the device to

reading array data (also applies to programming in

Erase Suspend mode). Once programming begins,

however, the device ignores reset commands until the

operation is complete.

The reset command may be written between the

sequence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must

be written to return to reading array data (also applies

to autoselect during Erase Suspend).

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to

read ing array da ta (a ls o applie s du r ing Erase

Suspend).

Autoselect Command Sequence

The autoselect command sequence allows the host

system to access the manufacturer and devices codes,

and determine whether or not a sector is protected.

The Command Definitions table shows the address

and data requirements. This method is an alternative to

that shown in the Autoselect Codes (High Voltage

AM29F200 数据表(PDF) 12 Page - Advanced Micro Devices

AM29F200 数据表(HTML) 12 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

数据表下载

链接网址

AM29F200 数据表(PDF) 12 Page - Advanced Micro Devices

AM29F200 数据表(HTML) 12 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

数据表 下载

链接网址

数据表下载