CS8401 datasheet(21/34 Pages) ETC

21 / 34 page

mitted. This sub-frame contains channel status

byte 0, bit 0. CBL returns low one bit period be-

fore the start of the frame that contains bit 0 of

channel status byte 16. CBL is the exact inverse

of flag 1 in mode 0 on the CS8401 (see Fig-

ure 11). CBL is not available when the CD

subcode port is enabled.

Figure 17 illustrates timing for stereo data input

on the audio port. Notice how CBL rises while

the right channel data (Right 0) is input, but the

previous left channel data (Left 0) is being trans-

mitted as the first sub-frame of the channel

status block (starting with preamble Z). The C,

U, and V input ports only need to be valid for a

short period after FSYNC changes. A sub-frame

includes one audio sample while a frame in-

cludes a stereo pair. A channel status (C.S.)

block contains 24 bytes of channel status and

384 audio samples (or 192 stereo pairs, or

frames, of samples).

Figure 17 shows the CUV ports as having left

and right bits (e.g. CUV0L, CUV0R). Since the

C.S. block is defined as 192 bits, or one bit per

frame, there are actually 2 C.S. blocks, one for

channel A (left) and one for channel B (right).

When inputting stereo audio data, both blocks

normally contain the same information, so C0L

and C0R from the input port pin are both chan-

nel status bit 0 of byte 0, which is defined as

professional/consumer. These first two bits from

the port, C0L and C0R, are logically OR’ed with

the inverse of PRO, since PRO is a dedicated

channel status pin defined as C.S. bit 0. Also, if

in professional mode, C1, C6, C7 and C9 are

dedicated C.S. pins. The inverse of C1 is logi-

cally OR’ed with channel status input port bits

C1L and C1R. In similar fashion, C6, C7 and C9

are OR’ed with their respective input bits. Also,

the C bits in CUV128L and CUV128R are both

channel status block bit 128, which is bit 0 of

channel status byte 16.

Transparent Mode

In certain applications it is desirable to receive

digital audio data with the CS8412 and retrans-

mit it with the CS8402A. In this case, channel

status, user and validity information must pass

through unaltered. For studio environments, AES

recommends that signal timing synchronization

be maintained throughout the studio. Frame syn-

chronization of digital audio signals input to and

output from a piece of equipment must be within

±5%.

The transparent mode of the CS8402A is se-

lected by setting TRNPT, pin 24, high. In this

mode, the CBL pin becomes an input, allowing

direct connection of the outputs of the CS8412

to the inputs of the CS8402A as shown in Fig-

ure 18 . The transmitter and receiver are

synchronized by the FSYNC signal. CBL speci-

fies the start of a new channel status block

boundary, allowing the transmit block structure

to be slaved to the block structure of the re-

ceiver. In the transparent mode, C, U, and V are

now transmitted with the current audio sample as

shown in Figure 17 (TRNPT high), and the dedi-

cated channel status pins are ignored. When in

the transparent mode, the propagation delay of

data through the CS8402A is set so that the total

propagation delay from the receive inputs of the

CS8412 to the transmit outputs of the CS8402A

is three frames.

MCK

CBL

FSYNC

SCK

SDATA

RXP

RXN

CS8412

TRNPT

TXP

TXN

V+

Data

Processing

CS8402A

Figure 18. Transparent Mode Interface

CS8402A

DS60F1

CS8401 数据表(PDF) 21 Page - List of Unclassifed Manufacturers

CS8401 数据表(HTML) 21 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表下载