 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
STM32F413MH 数据表(PDF) 82 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32F413MH 数据表(HTML) 82 Page - STMicroelectronics |
|
|
82 / 207 page  Electrical characteristics STM32F413xG/H 82/207 DocID029162 Rev 2 VIN Input voltage on RST, FT and TC pins(7) 2 V ≤ VDD ≤ 3.6 V –0.3 - 5.5 V VDD ≤ 2 V –0.3 - 5.2 Input voltage on TTa pins - - 0.3 - VDDA + 0.3 Input voltage on BOOT0 pin - 0 - 9 PD Power dissipation at TA = 85°C for range 6 or TA = 105°C for range 7(8) UFQFPN48 - - 625 mW WLCSP81 - - 504 LQFP64 - - 426 LQFP100 - - 465 LQFP144 - 571 UFBGA100 - - 351 UFBGA144 - - 417 Power dissipation at TA = 125°C for range 3(8) UFQFPN48 - - 156 WLCSP81 - - 126 LQFP64 - - 106 LQFP100 - - 116 LQFP144 - - 143 UFBGA100 - - 088 UFBGA144 - - 104 TA Ambient temperature for range 6 Maximum power dissipation –40 - 85 °C Low power dissipation(9) –40 - 105 Ambient temperature for range 7 Maximum power dissipation –40 - 105 Low power dissipation(9) –40 - 125 Ambient temperature for range 3 Maximum power dissipation –40 - 125 Low power dissipation(9) –40 - 130 TJ Junction temperature range Range 6 –40 - 105 Range 7 –40 - 125 Range 3 –40 - 130 1. VDD/VDDA minimum value of 1.7 V with the use of an external power supply supervisor (refer to Section 3.17.2: Internal reset OFF). 2. When the ADC is used, refer to Table 74: ADC characteristics. 3. If VREF+ pin is present, it must respect the following condition: VDDA-VREF+ < 1.2 V. 4. It is recommended to power VDD and VDDA from the same source. A maximum difference of 300 mV between VDD and VDDA can be tolerated during power-up and power-down operation. 5. Only the DM (PA11) and DP (PA12) pads are supplied through VDDUSB. For application where the VBUS (PA9) is directly connected to the chip, a minimum VDD supply of 2.7V is required. (some application examples are shown in appendix B) 6. Guaranteed by test in production 7. To sustain a voltage higher than VDD+0.3, the internal Pull-up and Pull-Down resistors must be disabled Table 16. General operating conditions (continued) Symbol Parameter Conditions Min Typ Max Unit |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
