6.42

IDT71342SA/LA

High-Speed 4K x 8 Dual-Port Static RAM with Semaphore

Industrial and Commercial Temperature Ranges

13

SEMAPHORE

REQUEST FLIP FLOP

DQ

SEMAPHORE

REQUEST FLIP FLOP

QD

WRITE

SEMAPHORE

READ

SEMAPHORE

READ

WRITE

RPORT

LPORT

2721 drw 14

semaphores on both sides should have a one written into them at

initialization from both sides to assure that they will be free when

needed.

Using Semaphores–Some

examples

Perhaps the simplest application of semaphores is their application

as resource markers for the IDT71342’s Dual-Port RAM. Say the 4K

x 8 RAM was to be divided into two 2K x 8 blocks which were to be

dedicated at any one time to servicing either the left or right port.

Semaphore 0 could be used to indicate the side which would control

the lower section of memory, and Semaphore 1 could be defined as the

indicator for the upper section of the memory.

To take a resource, in this example the lower 2K of Dual-Port RAM,

the processor on the left port could write and then read a zero into

Semaphore 0. If this task were successfully completed (a zero was

read back rather than a one), the left processor would assume control

of the lower 2K. Meanwhile, the right processor would attempt to

perform the same function. Since this processor was attempting to

gain control of the resource after the left processor, it would read back

a one in response to the zero it had attempted to write into Semaphore

0. At this point, the software could choose to try and gain control of the

second 2K section by writing, then reading a zero into Semaphore 1.

If it succeeded in gaining control, it would lock out the left side.

Once the left side was finished with its task, it would write a one to

Semaphore 0 and may then try to gain access to Semaphore 1. If

Semaphore 1 was still occupied by the right side, the left side could

undo its semaphore request and perform other tasks until it was able

to write, then read a zero into Semaphore 1. If the right processor

performs a similar task with Semaphore 0, this protocol would allow the

two processors to swap 2K blocks of Dual-Port RAM with each other.

The blocks do not have to by any particular size and can even be

variable, depending upon the complexity of the software using the

semaphore flags. All eight semaphores could be used to divide the

Dual-PortRAMorothersharedresourcesintoeightparts.Semaphores

can even be assigned different meanings on different sides rather than

being given a common meaning as was shown in the example above.

Semaphores are a useful form of arbitration in systems like disk

interfaces where the CPU must be locked out of a section of memory

during a transfer and the I/O device cannot tolerate any wait states.

With the use of semaphores, once the two devices had determined

which memory area was “off limits” to the CPU, both the CPU and the

I/Odevicescouldaccesstheirassignedportionsofmemorycontinuously

without any wait states.

Semaphores are also useful in applications where no memory

“WAIT” state is available on one or both sides. Once a semaphore

handshake has been performed, both processors can access their

assigned RAM segments at full speed.

Another application is in the area of complex data structures. In this

case, block arbitration is very important. For this application one

processor may be responsible for building and updating a data

structure. The other processor then reads and interprets that data

structure. If the interpreting processor reads an incomplete data

structure, a major error condition may exist. Therefore, some sort of

arbitration must be used between the two different processors. The

building processor arbitrates for the block, locks it and then is able to

go in and update the data structure. When the update is completed, the

data structure block is released. This allows the interpreting processor

to come back and read the complete data structure, thereby

guaranteeing a consistent data structure.

Figure 3. IDT71342 Semaphore Logic