PTS Series

www.vishay.com

Vishay Beyschlag

Revision: 08-Dec-15

2

Document Number: 28762

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

DIMENSIONS in millimeters

SOLDER PAD DIMENSIONS in millimeters

DESCRIPTION

A homogeneous film of platinum is deposited on a high

the correct temperature coefficient and stability. The

sensor-elements are covered by a protective coating

designed for electrical, mechanical and climatic protection.

The terminations receive a final pure matte tin on nickel

plating, the immunity against tin whisker growth has been

proven under extensive testing.

QUALITY

The result of the determined production is verified by an

extensive testing procedure performed on 100 % of the

individual sensors. Only accepted products are laid directly

into the paper tape in accordance with IEC 60286-3.

STORAGE

Solderability is specified for 2 years after production or

re-qualification. The permitted storage time is 2 years.

ASSEMBLY

The Pt-sensors are suitable for processing on automatic

SMD assembly systems. They are suitable for automatic

soldering using wave, reflow or vapour phase. The

encapsulation

is

resistant

to

all

cleaning

solvents

commonly used in the electronics industry, including

alcohols, esters and aqueous solutions. The suitability of

conformal coatings, if applied, shall be qualified by

appropriate means to ensure the long-term stability of the

whole system. The use of potting resins in close contact

with the coating or terminations is not allowed. For frequent

high temperature usage, thermal compatible substrates and

solder alloys should be used, to minimize any thermal

mismatch with the component.

All products comply with the CEFIC-EECA-EICTA list of

legal restrictions on hazardous substances.

This includes full compatibility with the following directives:

• 2000/53/EC End of Vehicle life Directive (ELV)

• 2000/53/EC Annex II to End of Vehicle Life Directive

(ELV II)

• 2011/65/EU

Restriction

of

the

use

of

Hazardous

Substances Directive (RoHS)

• 2002/96/EC Waste Electrical and Electronic Equipment

Directive (WEEE)

APPROVALS

The Pt-sensors are tested in accordance with

• IEC 60751

• IEC 60068 series

DIMENSIONS - PTS sensor types, mass and relevant physical dimensions

TYPE

H

L

W

MASS

(mg)

PTS 0603

0.45 + 0.1/- 0.05

1.55 +0.05 / -0.1

0.85 ± 0.1

> 75 % of W

0.3 + 0.15/- 0.2

0.3 + 0.15/- 0.2

1.9

PTS 0805

0.45 + 0.1/- 0.05

2.0 ± 0.1

1.25 ± 0.15

> 75 % of W

0.4 ± 0.2

0.4 ± 0.2

4.6

PTS 1206

0.55 ± 0.1

3.1 + 0.1/- 0.2

1.6 ± 0.15

> 75 % of W

0.5 ± 0.25

0.5 ± 0.25

9.2

RECOMMENDED SOLDERPAD DIMENSIONS

TYPE

WAVE SOLDERING

REFLOW SOLDERING

GY

X

Z

GY

X

Z

PTS 0603

0.55

1.1

1.1

2.75

0.65

0.7

0.95

2.05

PTS 0805

0.8

1.25

1.50

3.2

0.9

0.9

1.4

2.7

PTS 1206

1.4

1.5

1.9

4.4

1.5

1.15

1.75

3.8

Tb

Tt

L

H

W

WT

G

X

Y

Z