3825 Ohio Avenue • St. Charles, IL 60174

Phone: 800-SENSOR2 • Fax: 630-377-6495

©2011 System Sensor.

Product specifications subject to change without notice. Visit systemsensor.com for

current product information, including the latest version of this data sheet.

A05-0205-009 • 3/11 • #2651

Accessories

Ordering Information

Part No.

Description

5451

Fixed heat detector with rate-of-rise. Alarm point at 57.2°C (135°F). Must be mounted to one of the 400 Series Bases listed in Mounting Base

Guide.

Accessories

RA100Z

Remote annunciator for 2- or 4-wire systems, 3 to 32 V. Use with ion and photo plug-in detectors. Fits standard U.S. single-gang electrical box.

MOD400R

Detector sensitivity test tool. (See above.) Use with most analog or digital multimeters. Satisfies requirement of NFPA 72 for sensitivity testing.

(See above.)

EOLR-1

End of line relay for power supervision, 12/24 VDC, 4-wire only.

DUST45

Replacement protective dust cover for plug-in 400 Series.

M02-04-01

Test magnet.

M02-09-00

Test magnet with 32-inch telescoping handle.

XR5

Detector removal tool. Allows installation and/or removal of detector heads from base in high-ceiling installations.

XP-4

Extension pole for XR5. Comes in three 5 ft. sections.

The MOD400R Field Sensitivity

Test Module can be used with

any standard DC voltmeter or

multimeter to check the sensitivity

range of System Sensor’s detectors

(satisfies NFPA 72 requirement for

sensitivity testing).

Wiring

1

2

3

4

(+)

(–)

(–)

(+)

(–)

1

2

3

4

(–)

(+)

(+)

EOL

RESISTOR

(+)

(–)

(–)

(+)

(–)

OPTIONAL

OPTIONAL

RA400Z/

RA100Z

OPTIONAL FAULT TOLERANT WIRING

RA400Z/

RA100Z

B401

400 Series Plug-In Smoke Detector Specifications

Physical/Operating Specifications

Size

3.2˝ (8.1 cm) H; 4.0˝ (10.2 cm) Dia., unflanged base; 6.2˝ (15.7 cm) Dia., flanged base

Weight

0.3 lb (136 g)

Operating Temperature Range

32°F to 100°F (0°C to 38°C)

Humidity Range

10% to 93% RH non-condensing

Construction

Alarm Point

135°F (57.2°C) or 15°F/min rate-of-rise

Smoke Detector Spacing

On smooth ceilings (as defined in NFPA 72), spacing of 50 feet (2500 sq ft) may be used. Other spacing may be used

depending on ceiling height, high air movements, and other conditions or response requirements.

Standby Current

100 µA maximum

Operating Voltage/Alarm Current

Mounting base dependent (see Mounting Base Selection Guide below)

Mounting Base Selection Guide

Base Model Number

Version

Loop

Type

Current

Limit Resistor

Alarm

Contact Type

Nominal

Voltage

Current Draw

on Alarm (mA)

UL/EN-54

2-wire*

No

—

10 to 100**

*Functionality contingent on panel compatibility.

**Must be limited by control panel.

of operating at 12 and 24 VDC, they

cannot be used with the 5451 in 12

V applications.

Junction Box Selection Guide*

Single Gang

3.5”Octagon

4”Octagon

4”Square

50 mm

60 mm

75 mm

B401

No

No

No

No

Yes

Yes

No

*Box depth contingent on base and wire size. Refer to National Electrical Code of local applicable codes for appropriate recommendations.