MP7529BJS datasheet(4/12 Pages) EXAR

4 / 12 page

MP7529B

Rev. 2.00

ELECTRICAL CHARACTERISTICS (CONT’D)

°C

Tmin to Tmax

Parameter

Symbol

Min

Typ

Max

Min

Max

Units

Test Conditions/Comments

ANALOG OUTPUTS2

Output Capacitance

COUTA/B

120

DAC inputs all 1’s

COUTA/B

DAC inputs all 0’s

POWER SUPPLY

Supply Current

IDD

All digital inputs = 0 V or 5 V

All digital inputs = VIL or VIH

TIMING SPECIFICATIONS4

Chip Select to Write Set-Up Time

tCS

Chip Select to Write Hold Time

tCH

DAC Select to Write Set-Up Time

tAS

DAC Select to Write Hold Time

tAH

Data Valid to Write Set-Up Time

tDS

Data Valid to Write Hold Time

tDH

Write Pulse Width5

tWR

NOTES:

Specifications are subject to change without notice

Full Scale Range (FSR) is 10V for unipolar mode.

Guaranteed but not production tested.

Digital input levels should not go below GND or exceed the positive supply voltage, otherwise damage may occur.

See timing diagram.

tWR = 40ns minimum if tDH > 15ns (@T = 25°C)

ABSOLUTE MAXIMUM RATINGS (TA = +25

°C unless otherwise noted)1, 2, 3

VDD to GND

0 to +7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AGND to DGND

+1 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

(Functionality Guaranteed +0.5 V)

Digital Input Voltage to GND

GND –0.5 to VDD +0.5 V

. . . .

IOUTA, IOUTB to GND

GND –0.5 to VDD +0.5 V

. . . . . . . . . . .

VREFA, VREFB to GND

+25 V

. . . . . . . . . . . . . . . . . . . . . . . . . . .

VRFBA, VRFBB to GND

+25 V

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage Temperature

–65

°C to +150°C

. . . . . . . . . . . . . . . . .

Lead Temperature (Soldering, 10 seconds)

+300

°C

. . . . . .

Package Power Dissipation Rating to 75

°C

PDIP, SOIC, PLCC

900mW

. . . . . . . . . . . . . . . . . . . . . . . .

Derates above 75

°C

12mW/

°C

. . . . . . . . . . . . . . . . . . . . .

NOTES:

Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a

stress rating only and functional operation at or above this specification is not implied. Exposure to maximum rating

conditions for extended periods may affect device reliability.

Any input pin which can see a value outside the absolute maximum ratings should be protected by Schottky diode clamps

(HP5082-2835) from input pin to the supplies.

All inputs have protection diodes which will protect the device from short

transients outside the supplies of less than 100mA for less than 100

µs.

GND refers to AGND and DGND.

MP7529BJS 数据表(PDF) 4 Page - Exar Corporation

MP7529BJS 数据表(HTML) 4 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载