TC2014 datasheet(2/18 Pages) MICROCHIP

2 / 18 page

TC2014/2015/2185

DS21662C-page 2

 2003 Microchip Technology Inc.

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

Input Voltage ................................................................... 6.5V

Output Voltage ....................................... (– 0.3) to (VIN + 0.3)

Operating Temperature ......................... – 40°C < TJ < 125°C

Storage Temperature ................................. – 65°C to +150°C

Maximum Voltage on Any Pin ................ VIN +0.3V to – 0.3V

Maximum Junction Temperature ...................... ............ 150°C

† Notice: Stresses above those listed under "Maximum

Ratings" may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operation listings of this specification is not implied. Exposure

to maximum rating conditions for extended periods may affect

device reliability.

PIN FUNCTION TABLE

Name

Function

VIN

Unregulated Supply Input

GND

Ground Terminal

SHDN

Shutdown Control Input

Bypass

Reference Bypass Input

VOUT

Regulated Voltage Output

ELECTRICAL CHARACTERISTICS

Electrical Specifications: Unless otherwise specified, VIN = VR + 1V, IL = 100 µA, COUT = 3.3 µF, SHDN > VIH, TA = +25°C.

BOLDFACE type specifications apply for junction temperature of -40°C to +125°C.

Parameters

Sym

Min

Typ

Max

Units

Conditions

Input Operating Voltage

VIN

2.7

—

6.0

Note 1

Maximum Output

Current

IOUTMAX

—

TC2014

100

—

TC2015

150

—

TC2185

Output Voltage

VOUT

VR - 2.0% VR ± 0.4% VR + 2.0%

Note 2

VOUT Temperature

Coefficient

TCVOUT

—20

—

ppm/°C Note 3

—

Line Regulation

∆VOUT/∆VIN

—0.05

0.5

%(VR + 1V) < VIN < 6V

Load Regulation

(Note 4)

∆VOUT/VOUT

-1.0

0.33

+1.0

TC2014;TC2015: IL = 0.1 mA to IOUTMAX

-2.0

0.43

+2.0

TC2185: IL = 0.1 mA to IOUTMAX Note 4

Dropout Voltage

VIN - VOUT

—2

—

Note 5

IL = 100 µA

—45

IL = 50 mA

—90

140

TC2015; TC2185 IL = 100 mA

—140

210

TC2185

IL = 150 mA

Supply Current

IIN

—55

µA

SHDN = VIH, IL=0

Shutdown Supply

Current

IINSD

—

0.05

0.5

µA

SHDN = 0V

Note 1: The minimum VIN has to meet two conditions: VIN = 2.7V and VIN = VR + VDROPOUT.

2: VR is the regulator output voltage setting. For example: VR = 1.8V, 2.7V, 2.8V, 2.85V, 3.0V, 3.3V.

4: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested

over a load range from 1.0 mA to the maximum specified output current. Changes in output voltage due to heating

effects are covered by the thermal regulation specification.

5: Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal

value at a V differential.

6: Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,

excluding load or line regulation effects. Specifications are for a current pulse equal to IMAX at VIN = 6V for T = 10 msec.

7: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction tem-

perature and the thermal resistance from junction-to-air (i.e. TA, TJ, θJA).

8: Time required for VOUT to reach 95% of VR (output voltage setting), after VSHDN is switched from 0 to VIN.

TCVOUT

VOUTMAX VOUTMIN

–

() 10

–

VOUT

∆

----------------------------------------------------------------------------

TC2014 数据表(PDF) 2 Page - Microchip Technology

TC2014 数据表(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

数据表下载

链接网址

TC2014 数据表(PDF) 2 Page - Microchip Technology

TC2014 数据表(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

数据表 下载

链接网址

数据表下载