STM32L443CC datasheet(20/207 Pages) STMICROELECTRONICS

20 / 207 page

Functional overview

STM32L443CC STM32L443RC STM32L443VC

20/207

DocID028739 Rev 2

3.7

Boot modes

At startup, BOOT0 pin or nSWBOOT0 option bit, and BOOT1 option bit are used to select

one of three boot options:

•

Boot from user Flash

•

Boot from system memory

•

Boot from embedded SRAM

BOOT0 value may come from the PH3-BOOT0 pin or from an option bit depending on the

value of a user option bit to free the GPIO pad if needed.

A Flash empty check mechanism is implemented to force the boot from system flash if the

first flash memory location is not programmed and if the boot selection is configured to boot

from main flash.

The boot loader is located in system memory. It is used to reprogram the Flash memory by

using USART, I2C, SPI, CAN and USB FS in Device mode through DFU (device firmware

upgrade).

3.8

Cyclic redundancy check calculation unit (CRC)

The CRC (cyclic redundancy check) calculation unit is used to get a CRC code using a

configurable generator polynomial value and size.

Among other applications, CRC-based techniques are used to verify data transmission or

storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of

verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of

the software during runtime, to be compared with a reference signature generated at link-

time and stored at a given memory location.

3.9

Power supply management

3.9.1

Power supply schemes

•

VDD = 1.71 to 3.6 V: external power supply for I/Os (VDDIO1), the internal regulator and

the system analog such as reset, power management and internal clocks. It is provided

externally through VDD pins.

•

VDDA = 1.62 V (ADCs/COMPs) / 1.8 (DACs/OPAMP) to 3.6 V: external analog power

supply for ADCs, DACs, OPAMP, Comparators and Voltage reference buffer. The VDDA

voltage level is independent from the VDD voltage.

•

VDDUSB = 3.0 to 3.6 V: external independent power supply for USB transceivers. The

VDDUSB voltage level is independent from the VDD voltage.

•

VLCD = 2.5 to 3.6 V: the LCD controller can be powered either externally through VLCD

pin, or internally from an internal voltage generated by the embedded step-up

converter.

•

VBAT = 1.55 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and

backup registers (through power switch) when VDD is not present.

Note:

When the functions supplied by VDDA or VDDUSB are not used, these supplies should

preferably be shorted to VDD.

STM32L443CC 数据表(PDF) 20 Page - STMicroelectronics

STM32L443CC 数据表(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载