Z86L02 datasheet(19/37 Pages) ZILOG

19 / 37 page

Z86C02/E02/L02

Zilog

Cost Effective, 512-Byte ROM CMOS Z8® Microcontrollers

DS96DZ80301

P R E L I M I N A R Y

FUNCTIONAL DESCRIPTION

The following special functions have been incorporated

into the Z86C02/E02/L02 devices to enhance the standard

Z8 core architecture to provide the user with increased de-

sign flexibility.

RESET. This function is accomplished by means of a Pow-

er-On Reset or a Watch-Dog Timer Reset. Upon power-

up, the Power-On Reset circuit waits for TPOR ms, plus 18

clock cycles, then starts program execution at address

000C (Hex) (Figure 11). The control registers' reset value

is shown in Table 4.

Power-On Reset (POR). A timer circuit clocked by a ded-

icated on-board RC oscillator is used for a POR timer func-

tion. The POR time allows VCC and the oscillator circuit to

stabilize before instruction execution begins. The POR

timer circuit is a one-shot timer triggered by one of the four

following conditions:

Power bad to power good status

Stop-Mode Recovery

WDT time-out

WDH time-out (in Halt Mode)

WDT time-out (in Stop Mode)

Watch-Dog Timer Reset. The WDT is a retriggerable

one-shot timer that resets the Z8 if it reaches its terminal

count. The WDT is initially enabled by executing the WDT

instruction and is retriggered on subsequent execution of

the WDT instruction. The timer circuit is driven by an on-

board RC oscillator. If the permanent WDT option is select-

ed then the WDT is enabled after reset and operates in

RUN Mode, HALT mode, STOP mode and cannot be dis-

abled. If the permanent WDT option is not selected then

the WDT, when enabled by the user's software, does not

operate in STOP Mode, but it can operate in HALT Mode

by using a WDH instruction.

Figure 11. Internal Reset Conﬁguration

POR

(Cold Start)

P27

(Stop Mode)

Delay Line

POR ms

18 CLK

Reset Filter

Chip

Reset

XTAL OSC

INT OSC

Table 4. Control Register

Reset Condition

Addr Reg.

D7 D6 D5 D4 D3 D2 D1 D0 Comments

SPL

00000000

GPR

00000000

FLAGS UUUUUUUU

IMR

UUUUUUU

IRQ

U U

000000 IRQ3 is used

for positive

edge

detection

IPR

UUUUUUUU

P01M

U U U

U U

F7*

P3M

UUUUUU

0 P2 open-drain

F6*

P2M

11111111 Inputs after

reset

PRE1

UUUUUU

UUUUUUUU

TMR

00000000

Note:

*Registers are not reset after a STOP-Mode Recovery

using P27 pin. A subsequent reset will cause these control

registers to be reconfigured as shown in Table 4 and the

user must avoid bus contention on the port pins or it may

affect device reliability.

Z86L02 数据表(PDF) 19 Page - Zilog, Inc.

Z86L02 数据表(HTML) 19 Page - Zilog, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

数据表下载

链接网址

Z86L02 数据表(PDF) 19 Page - Zilog, Inc.

Z86L02 数据表(HTML) 19 Page - Zilog, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

数据表 下载

链接网址

数据表下载