 |
数据搜索系统，热门电子元器件搜索 |
|
|
数据搜索系统，热门电子元器件搜索 |
|
ST7LITE1 数据表(PDF) 128 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST7LITE1 数据表(HTML) 128 Page - STMicroelectronics |
|
|
128 / 131 page  ST7LITE1 128/131 16 IMPORTANT NOTES 16.1 EXECUTION OF BTJX INSTRUCTION When testing the address $FF with the "BTJT" or "BTJF" instructions, the CPU may perform an in- correct operation when the relative jump is nega- tive and performs an address page change. To avoid this issue, including when using a C com- piler, it is recommended to never use address $00FF as a variable (using the linker parameter for example). 16.2 ADC CONVERSION SPURIOUS RESULTS Spurious conversions occur with a rate lower than 50 per million. Such conversions happen when the measured voltage is just between 2 consecutive digital values. Workaround A software filter should be implemented to remove erratic conversion results whenever they may cause unwanted consequences. 16.3 A/ D CONVERTER ACCURACY FOR FIRST CONVERSION When the ADC is enabled after being powered down (for example when waking up from HALT, ACTIVE-HALT or setting the ADON bit in the AD- CCSR register), the first conversion (8-bit or 10- bit) accuracy does not meet the accuracy specified in the datasheet. Workaround In order to have the accuracy specified in the da- tasheet, the first conversion after a ADC switch-on has to be ignored. 16.4 NEGATIVE INJECTION IMPACT ON ADC ACCURACY Injecting a negative current on an analog input pins significantly reduces the accuracy of the AD Converter. Whenever necessary, the negative in- jection should be prevented by the addition of a Schottky diode between the concerned I/Os and ground. Injecting a negative current on digital input pins degrades ADC accuracy especially if performed on a pin close to ADC channel in use. 16.5 CLEARING ACTIVE INTERRUPTS OUTSIDE INTERRUPT ROUTINE When an active interrupt request occurs at the same time as the related flag or interrupt mask is being cleared, the CC register may be corrupted. Concurrent interrupt context The symptom does not occur when the interrupts are handled normally, i.e. when: - The interrupt request is cleared (flag reset or in- terrupt mask) within its own interrupt routine - The interrupt request is cleared (flag reset or in- terrupt mask) within any interrupt routine - The interrupt request is cleared (flag reset or in- terrupt mask) in any part of the code while this in- terrupt is disabled If these conditions are not met, the symptom can be avoided by implementing the following se- quence: Perform SIM and RIM operation before and after resetting an active interrupt request Ex: SIM reset flag or interrupt mask RIM 16.6 USING PB4 AS EXTERNAL INTERRUPT PB4 cannot be used as an external interrupt in HALT mode because the port pin PB4 is not active in this mode. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
