AD9481 datasheet(21/29 Pages) AD

21 / 29 page

AD9481

Rev. 0 | Page 20 of 28

Table 9. S1 Voltage Levels

S1 Voltage

Data Format

Duty Cycle

Stabilizer

(0.9 × AVDD)

→ AVDD

Offset binary

Disabled

(2/3 × AVDD) ± (0.1 × AVDD)

Offset binary

Enabled

(1/3 × AVDD) ± (0.1 × AVDD)

Twos complement

Enabled

AGND

→ (0.1 × AVDD)

Twos complement

Disabled

DIGITAL OUTPUTS

The CMOS digital outputs are TTL-/CMOS-compatible for

lower power consumption. The outputs are biased from a

separate supply (DRVDD), allowing easy interface to external

logic. The outputs are CMOS devices that swing from ground to

DRVDD (with no dc load). It is recommended to minimize the

capacitive load the ADC drives by keeping the output traces

short (< 2 inch, for a total CLOAD < 5 pF). When operating in

CMOS mode, it is also recommended to place low value series

damping resistors on the data lines close to the ADC to reduce

switching transient effects on performance.

Table 10. Output Coding (FS = 1 V)

Code

(VIN+) − (VIN−)

Offset Binary

Twos Complement

255

> +0.512 V

1111 1111

0111 1111

255

+0.512 V

1111 1111

0111 1111

254

+0.508 V

1111 1110

0111 1110

•

129

+0.004 V

1000 0001

0000 0001

128

+0.0 V

1000 0000

0000 0000

127

−0.004 V

0111 1111

1111 1111

•

−0.504 V

0000 0010

1000 0010

−0.508 V

0000 0001

1000 0001

−0.512 V

0000 0000

1000 0000

< −0.512 V

0000 0000

1000 0000

INTERLEAVING TWO AD9481s

Instrumentation applications may prefer to interleave (or ping-

pong) two AD9481s to achieve twice the sample rate, or

500 MSPS. In these applications, it is important to match the

gain and offset of the two ADCs. Varying the reference voltage

allows the gain of the ADCs to be adjusted; external dc offset

compensation can be used to reduce offset mismatch between

two ADCs. The sampling phase offset between the two ADCs

is extremely important as well and requires very low skew

between clock signals driving the ADCs (< 2 ps clock skew

for a 100 MHz analog input frequency).

DATA CLOCK OUT

A data clock is available at DCO+ and DCO−. These clocks can

facilitate latching off-chip, providing a low skew clocking

solution. The on-chip delay of the DCO clocks tracks with the

on-chip delay of the data bits, (under similar loading) such that

the variation between tPD and tCPD is minimized. It is

recommended to keep the trace lengths on the data and DCO

pins matched and 2 inches maximum. A series damping resistor

at the clock outputs is also recommended. The DCO outputs

can be disabled and placed in a high impedance state by tying

S3 to ground (tie to AVDD for DCO active). Switching both

into and out of high impedance is accomplished in 4 ns from S3

switching.

POWER-DOWN INPUT

The ADC can be placed into a low power state by setting the

PDWN pin to AVDD. Time to go into (or come out of) power

down equals 30 ns typically from PDWN switching.

AD9481 数据表(PDF) 21 Page - Analog Devices

AD9481 数据表(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

数据表下载

链接网址

AD9481 数据表(PDF) 21 Page - Analog Devices

AD9481 数据表(HTML) 21 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

数据表 下载

链接网址

数据表下载