AD6644STSLASHPCB datasheet(16/25 Pages) AD

16 / 25 page

AD6644

Rev. D | Page 15 of 24

THEORY OF OPERATION

The AD6644 analog-to-digital converter (ADC) employs a

three-stage subrange architecture. This design approach

achieves the required accuracy and speed while maintaining

low power and small die size.

As shown in the functional block diagram, the AD6644 has

complementary analog input pins, AIN and AIN. Each analog

input is centered at 2.4 V and swings ±0.55 V around this

reference (Figure 21). Because AIN and AIN are 180° out of

phase, the differential analog input signal is 2.2 V peak-to-peak.

Both analog inputs are buffered prior to the first track-and-hold,

TH1. The high state of the ENCODE pulse places TH1 in hold

mode. The held value of TH1 is applied to the input of a 5-bit

coarse ADC1. The digital output of ADC1 drives a 5-bit digital-

to-analog converter (DAC1). DAC1 requires 14 bits of precision,

which is achieved through laser trimming. The output of DAC1

is subtracted from the delayed analog signal at the input of TH3

to generate a first residue signal. TH2 provides an analog

pipeline delay to compensate for the digital delay of ADC1.

The first residue signal is applied to a second conversion stage

consisting of a 5-bit ADC2, 5-bit DAC2, and pipeline TH4. The

second DAC requires 10 bits of precision, which is met by the

process with no trim. The input to TH5 is a second residue

signal generated by subtracting the quantized output of DAC2

from the first residue signal held by TH4. TH5 drives a final

6-bit ADC3.

The digital outputs from ADC1, ADC2, and ADC3 are added

together and corrected in the digital error correction logic to

generate the final output data. The result is a 14-bit parallel

digital CMOS-compatible word, coded as twos complement.

APPLYING THE AD6644

Encoding the AD6644

The AD6644 encode signal must be a high quality, extremely

low phase noise source to prevent degradation of performance.

Maintaining 14-bit accuracy places a premium on encode clock

phase noise. SNR performance can easily degrade by 3 dB to

4 dB with 70 MHz input signals when using a high jitter clock

source. See the Analog Devices Application Note AN-501,

Aperture Uncertainty and ADC System Performance

, for

complete details.

For optimum performance, the AD6644 must be clocked

differentially. The encode signal is usually ac-coupled into the

ENCODE and ENCODE pins via a transformer or capacitors.

These pins are biased internally and require no additional bias.

See Figure 27 for one preferred method for clocking the AD6644.

The clock source (low jitter) is converted from single-ended to

differential using an RF transformer. The back-to-back Schottky

diodes across the secondary windings of the transformer limit

clock excursions into the AD6644 to approximately 0.8 V p-p

differential. This helps prevent the large voltage swings of the

clock from feeding through to the other portions of the

AD6644, and limits the noise presented to the ENCODE inputs.

A crystal clock oscillator can also be used to drive the RF

transformer if an appropriate limiting resistor (typically 100 Ω)

is placed in series with the primary winding of the transformer.

ENCODE

T1-4T

AD6644

HSMS2812

DIODES

0.1µF

100Ω

CLOCK

SOURCE

Figure 27. Crystal Clock Oscillator—Differential Encode

If a low jitter ECL/PECL clock is available, another option is to

ac-couple a differential ECL/PECL signal to the encode input

pins as shown in Figure 28. A device that offers excellent jitter

performance is the MC100LVEL16 (or another in the same

family) from Motorola.

ENCODE

AD6644

ECL/

PECL

0.1µF

Figure 28. Differential ECL for Encode

Analog Input

As with most new high speed, high dynamic range ADCs, the

analog input to the AD6644 is differential. Differential inputs

allow much improvement in performance on-chip as signals are

processed through the analog stages. Most of the improvement

is a result of differential analog stages having high rejection of

even-order harmonics. There are also benefits at the PCB level.

First, differential inputs have high common-mode rejection of

stray signals such as ground and power noise. In addition, they

provide good rejection of common-mode signals such as local

oscillator feedthrough.

The AD6644 input voltage range is offset from ground by 2.4 V.

Each analog input connects through a 500 Ω resistor to a 2.4 V

bias voltage and to the input of a differential buffer (Figure 21).

The resistor network on the input properly biases the followers

for maximum linearity and range. Therefore, the analog source

driving the AD6644 should be ac-coupled to the input pins.

Because the differential input impedance of the AD6644 is

1 kΩ, the analog input power requirement is only −2 dBm,

simplifying the driver amplifier in many cases. To take full

advantage of this high input impedance, a 20:1 transformer is

required. This is a large ratio and could result in unsatisfactory

performance. In this case, a lower step-up ratio can be used.

The recommended method for driving the analog input of the

AD6644 is to use a 4:1 RF transformer. For example, if RT is set

to 60.4 Ω and RS is set to 25 Ω, along with a 4:1 transformer, the

AD6644ST/PCB 数据表(PDF) 16 Page - Analog Devices

AD6644ST/PCB 数据表(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

数据表下载

链接网址

AD6644ST/PCB 数据表(PDF) 16 Page - Analog Devices

AD6644ST/PCB 数据表(HTML) 16 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

数据表 下载

链接网址

数据表下载