| 数据搜索系统,热门电子元器件搜索 |
|
TLV1543MFKB 数据表(PDF) 6 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TLV1543MFKB 数据表(HTML) 6 Page - Texas Instruments |
|
6 / 26 page ![]() TLV1543C, TLV1543I, TLV1543M 3.3V 10BIT ANALOGTODIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 ANALOG INPUTS SLAS072E − DECEMBER 1992 − REVISED JANUARY 2004 6 WWW.TI.COM Table 2. Analog-Channel-Select Address ANALOG INPUT SELECTED VALUE SHIFTED INTO ADDRESS INPUT SELECTED BINARY HEX A0 0000 0 A1 0001 1 A2 0010 2 A3 0011 3 A4 0100 4 A5 0101 5 A6 0110 6 A7 0111 7 A8 1000 8 A9 1001 9 A10 1010 A Table 3. Test-Mode-Select Address INTERNAL SELF-TEST VOLTAGE SELECTED† VALUE SHIFTED INTO ADDRESS INPUT OUTPUT RESULT (HEX)‡ VOLTAGE SELECTED† BINARY HEX OUTPUT RESULT (HEX)‡ V ref ) –Vref– 1011 B 200 V ref ) –Vref– 2 1011 B 200 Vref − 1100 C 000 Vref + 1101 D 3FF † Vref+ is the voltage applied to the REF+ input, and Vref− is the voltage applied to the REF− input. ‡ The output results shown are the ideal values and vary with the reference stability and with internal offsets. converter and analog input The CMOS threshold detector in the successive-approximation conversion system determines each bit by examining the charge on a series of binary-weighted capacitors (see Figure 1). In the first phase of the conversion process, the analog input is sampled by closing the SC switch and all ST switches simultaneously. This action charges all the capacitors to the input voltage. In the next phase of the conversion process, all ST and SC switches are opened and the threshold detector begins identifying bits by identifying the charge (voltage) on each capacitor relative to the reference (REF −) voltage. In the switching sequence, ten capacitors are examined separately until all ten bits are identified and the charge-convert sequence is repeated. In the first step of the conversion phase, the threshold detector looks at the first capacitor (weight = 512). Node 512 of this capacitor is switched to the REF+ voltage, and the equivalent nodes of all the other capacitors on the ladder are switched to REF −. If the voltage at the summing node is greater than the trip point of the threshold detector (approximately one-half the VCC voltage), a bit 0 is placed in the output register and the 512-weight capacitor is switched to REF −. If the voltage at the summing node is less than the trip point of the threshold detector, a bit 1 is placed in the register and the 512-weight capacitor remains connected to REF + through the remainder of the successive-approximation process. The process is repeated for the 256-weight capacitor, the 128-weight capacitor, and so forth down the line until all bits are counted. With each step of the successive-approximation process, the initial charge is redistributed among the capacitors. The conversion process relies on charge redistribution to count and weigh the bits from MSB to LSB. |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |