TSM103WID datasheet(4/7 Pages) STMICROELECTRONICS

4 / 7 page

TSM103W

ELECTRICAL CHARACTERISTICS

4/7

OPERATOR 1 (op-amp with non-inverting input connected to the internal Vref)

VCC

+ = +5V, V

- = Ground, T

amb = 25°C (unless otherwise specified)

GBP

Gain Bandwidth Product

VCC = 30V,RL = 2k, CL = 100pF

f = 100kHz, Vin = 10mV

0.5

0.9

MHz

THD

Total Harmonic Distortion

f = 1kHz

AV = 20dB,RL = 2k, VCC = 30V

CL = 100pF, Vo = 2Vpp

0.02

Equivalent Input Noise Voltage

f = 1kHz, Rs = 100

Ω

Vcc = 30V

nV/

√Hz

The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end

of the common-mode voltage range is VCC

+ - 1.5V. Both inputs can go to Vcc+ 0.3V without damage.

Symbol

Parameter

Min.

Typ.

Max.

Unit

Vio

Input Offset Voltage

Vicm = 0V

TSM103WA, Tamb = 25°

Tmin. ≤ Tamb ≤ Tmax.

TSM103W, Tamb = 25°

Tmin. ≤ Tamb ≤ Tmax.

0.5

DVio

Input Offset Voltage Drift

µV/°C

Iib

Input Bias Current

negative input

Avd

Large Signal Voltage Gain

VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V

Tmin. ≤ Tamb ≤ Tmax

100

V/mV

SVR

Supply Voltage Rejection Ratio

Vicm = 0V

VCC

+ = 5V to 30V

100

Isource

Output Current Source

Vo = 2V

VCC = +15V, Vid = +1V

Short Circuit to Ground

VCC = +15V

Isink

Output Current Sink

Vid = -1V,

VCC = +15V, Vo = 2V

VCC = +15V, Vo = 0.2V

µA

VOH

High Level Output Voltage

VCC

+ = 30V

Tamb = 25°C, RL = 2k

Tmin. ≤ Tamb ≤ Tmax.

Tamb = 25°C, RL = 10k

Tmin. ≤ Tamb ≤ Tmax.

VOL

Low Level Output Voltage

RL = 10k

Tmin. ≤ Tamb ≤ Tmax.

520

Slew Rate at Unity Gain

Vi = 0.5 to 2V, VCC = 15V

RL = 2k, CL = 100pF, unity gain

0.2

0.4

µs

Symbol

Parameter

Min.

Typ.

Max.

Unit

TSM103WID 数据表(PDF) 4 Page - STMicroelectronics

TSM103WID 数据表(HTML) 4 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7

数据表下载

链接网址

TSM103WID 数据表(PDF) 4 Page - STMicroelectronics

TSM103WID 数据表(HTML) 4 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7

数据表 下载

链接网址

数据表下载