| 数据搜索系统,热门电子元器件搜索 |
|
AD5560JBCZ 数据表(PDF) 49 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD5560JBCZ 数据表(HTML) 49 Page - Analog Devices |
|
49 / 67 page ![]() AD5560 Data Sheet Rev. E | Page 48 of 66 Table 18. DPS Register 1 Address Default Data Bits, MSB First 0x2 0x0000 Bit Name Function 15 SW-INH This bit enables the force amplifier when high and disables the amplifier when low. This bit is AND’d with the HW_INH hardware inhibit pin. 14 Reserved Reserved, set to 0. 13 I[2:0] Current range addressing. These bits allow selection of the required current range. 12 11 I Action 0 ±5 µA current range. 1 ±25 µA current range. 2 ±250 µA current range. 3 ±2.5 mA current range. 4 ±25 mA current range. 5 External Range 2. 6 External Range 1. 7 Reserved. 10 CMP[1:0] Comparator function. CMP1 acts as a comparator output enable, whereas CMP0 selects between a comparing DUT current or voltage; by default, the comparators are high-Z on power-on. 9 CMP Action 0 Comparator outputs high-Z. 1 Comparator outputs high-Z. 2 Compare DUT current. 3 Compare DUT voltage. 8 ME[3:0] Bits ME[3:0] allow selection of the required measure mode, allowing the MEASOUT line to be disabled; connect to the temperature sensor or enable it for measurement. ME[3] is MEASOUT enable/disable; when high, MEASOUT is enabled, and ME[2:0] can be used to preselect the measuring parameter. Where a number of MEASOUT lines are connected together and passed to a common ADC, this function can allow for much faster measurement time between channels because the slew time of the measurement buffer is reduced. For details on diagnostic functions, see Address 0x7, the diagnostic register. 7 6 5 ME[2:0] Action 0 MEASOUT high-Z. 1 Connect MEASOUT to ISENSE. 2 Connect MEASOUT to VSENSE. 3 Connect MEASOUT to KSENSE. 4 Connect MEASOUT to TSENSE. 5 Connect MEASOUT to DUTGND SENSE. 6 Connect MEASOUT to diagnostic functions: DIAG A (see Address 0x7). 7 Connect MEASOUT to diagnostic functions: DIAG B (see Address 0x7). 4 CLEN Clamp enable; set high to enable the clamp; set low to disable the clamp. This bit is OR’d with the hardware CLEN pin. 3:0 Unused Set to 0. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |