SC14WAMDECT-SF datasheet(29/36 Pages) DIALOG

29 / 36 page

Datasheet

Revision 3.0

23-Jul-2015

CFR0011-120-00-FM Rev 5

29 of 36

SC14WAMDECT SF

Wireless Audio Module

FINAL

9.0 Notices to OEM

The end product has to be certified again when it

has been programmed with other software than the

Dialog standard software stack for portable part

and/or uses one or two external antenna(s). (See

[1] for more detailed information).

9.1 FCC REQUIREMENTS REGARDING THE END

PRODUCT AND THE END USER

The end product that the module is integrated into must

be marked as follows:

“Contains Transmitter Module FCC ID: Y82-SC14S /

IC: 9576A-SC14S”

The literature provided to the end user must include the

following wording:

FCC compliance statement

This device complies with Part 15 of the FCC Rules for

only portable part.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired opera-

tion of the device.

Module transmetteur ID IC: 9576A-SC14S.

Son fonctionnement est soumis aux deux conditions

suivantes: (1) cet appareil ne doit pas causer d’interfé-

rences nuisibles et (2) appareil doit accepter toute

interférence reçue, y compris les interférences qui peu-

vent perturber le fonctionnement.

Changes or modifications to the equipment not

expressly approved by the Party responsible for com-

pliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generate, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a par-

ticular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and

receiver

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV tech-

nician for help.

Privacy of communications may not be ensured when

using this phone.

9.2 INDUSTRY CANADA REQUIREMENTS

REGARDING THE END PRODUCT AND THE END

USER

The host device shall be properly labelled to identify

the modules within the host device. The Industry Can-

ada certification label of a module shall be clearly visi-

ble at all times when installed in the host device,

otherwise the host device must be labelled to display

the Industry Canada certification number of the mod-

ule, preceded by the words "Contains transmitter mod-

ule", or the word "Contains", or similar wording

expressing the same meaning, as follows:

Contains transmitter module IC: 9576A-SC14S

L'appareil hôte doit être étiqueté comme il faut pour

permettre l'identification des modules qui s'y trouvent.

L'étiquette de certification d'Industrie Canada d'un

module donné doit être posée sur l'appareil hôte à un

endroit bien en vue en tout temps. En l'absence d'éti-

quette, l'appareil hôte doit porter une etiquette donnant

le numéro de certification du module d'Industrie Can-

ada, précédé des mots " Contient un module d'émis-

sion ", du mot " Contient " ou d'une formulation

similaire exprimant le même sens, comme suit :

Contient le module d'émission IC: 9576A-SC14S

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause

interference, and (2) this device must accept any inter-

ference, including interference that may cause unde-

sired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie

Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux condi-

tions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter

tout brouillage radioélectrique subi, même si le brouil-

lage est susceptible d'en compromettre le fonctionne-

ment.

CAN ICES-3 (B)/NMB-3(B)

SC14WAMDECT-SF 数据表(PDF) 29 Page - Dialog Semiconductor

SC14WAMDECT-SF 数据表(HTML) 29 Page - Dialog Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载