AM29PL320DB60RWPI datasheet(29/50 Pages) SPANSION

29 / 50 page

October 2, 2003

Am29PL320D

WRITE OPERATION STATUS

The device provides several bits to determine the sta-

tus of a write operation: DQ2, DQ3, DQ5, DQ6, and

DQ7. Table 15 and the following subsections describe

the functions of these bits. DQ7 and DQ6 each offer a

method for determining whether a program or erase

operation is complete or in progress. These three bits

are discussed first.

DQ7: Data# Polling

The Data# Polling bit, DQ7, indicates to the host

system whether an Embedded Algorithm is in progress

or completed, or whether the device is in Erase

Suspend. Data# Polling is valid after the rising edge

of the final WE# pulse in the program or erase com-

mand sequence.

During the Embedded Program algorithm, the device

outputs on DQ7 the complement of the datum pro-

grammed to DQ7. This DQ7 status also applies to

programming during Erase Suspend. When the Em-

bedded Program algorithm is complete, the device

outputs the datum programmed to DQ7. The system

must provide the program address to read valid status

information on DQ7. If a program address falls within a

protected sector, Data# Polling on DQ7 is active for ap-

proximately 1 µs, then the device returns to reading

array data.

During the Embedded Erase algorithm, Data# Polling

produces a “0” on DQ7. When the Embedded Erase

algorithm is complete, or if the device enters the Erase

Suspend mode, Data# Polling produces a “1” on DQ7.

This is analogous to the complement/true datum out-

put described for the Embedded Program algorithm:

the erase function changes all the bits in a sector to

“1”; prior to this, the device outputs the “complement,”

or “0.” The system must provide an address within any

of the sectors selected for erasure to read valid status

information on DQ7.

After an erase command sequence is written, if all sec-

tors selected for erasing are protected, Data# Polling

on DQ7 is active for approximately 100 µs, then the de-

vice returns to reading array data. If not all selected

sectors are protected, the Embedded Erase algorithm

erases the unprotected sectors, and ignores the se-

lected sectors that are protected.

When the system detects DQ7 has changed from the

complement to true data, it can read valid data at

DQ7–DQ0 on the

following read cycles. This is be-

cause DQ7 may change asynchronously with DQ0–

DQ6 while Output Enable (OE#) is asserted low. See

Figure 18 in the “AC Characteristics” section.

Table 15 shows the outputs for Data# Polling on DQ7.

Figure 5 shows the Data# Polling algorithm.

Notes:

1. VA = Valid address for programming. During a sector

erase operation, a valid address is an address within any

sector selected for erasure. During chip erase, a valid

address is any non-protected sector address.

2. DQ7 should be rechecked even if DQ5 = “1” because

DQ7 may change simultaneously with DQ5

Figure 5.

Data# Polling Algorithm

DQ7 = Data?

Yes

DQ5 = 1?

Yes

FAIL

PASS

Read DQ7–DQ0

Addr = VA

Read DQ7–DQ0

Addr = VA

DQ7 = Data?

START

AM29PL320DB60RWPI 数据表(PDF) 29 Page - SPANSION

AM29PL320DB60RWPI 数据表(HTML) 29 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

数据表下载