Input

Description

voltage

Type

Order No.

Pcs./ Pkt.

PLC interface, consisting of

base terminal block PLC-BSP…SEN and

pluggable miniature optical coupler

24 V DC

(see catalog part 6, page 33),

120 V AC/110 V DC

for mounting on

3

equipped with

input optical coupler

PLC-OSP- 24DC/48DC/100/SEN

29 67 57 8

10

PLC-OSP-120UC/48DC/100/SEN

29 67 58 1

10

PLC-OSP-230UC/48DC/100/SEN

29 67 59 4

10

PLC interface, consisting of

base terminal block PLC-BSP…SEN and

pluggable miniature optical coupler

24 V DC

(see catalog part 6, page 33),

120 V AC/110 V DC

for mounting on

3

equipped with

power optical coupler

PLC-OSP- 24DC/24DC/2/SEN

29 67 51 0

10

PLC-OSP-120UC/24DC/2/SEN

29 67 52 3

10

PLC-OSP-230UC/24DC/2/SEN

29 67 53 6

10

Technical data

Input optical coupler

Power optical coupler

Input data

Switching level

1 signal (“H”)

0 signal (“L”)

Input circuit

24 V DC

120, 230 V AC/DC

24 V DC

120 V AC/

24 V DC

120 V AC/

110 V DC

110 V DC

230 V AC/

230 V AC/

0.8-1.2

0.8-1,1

0.8-1.2

0.8-1.1

8 mA

4 mA

9 mA

4 mA

20 µs

6 ms

20 µs

6 ms

300 µs

10 ms

500 µs

10 ms

300 Hz

10 Hz

300 Hz

10 Hz

operation indicator, polarity protection diode, damping diode

operation indicator, bridge rectifier

Output data

Max. switching voltage

Min. switching voltage

Limiting continuous current

Max. inrush current

Min. switching current

Output connection

Output circuit

Voltage drop at max. limiting continuous current

PLC-O…/48DC/100/SEN

PLC-O…/24DC/2/SEN

48 V DC

33 V DC

3 V DC

3 V DC

100 mA

2 A (see derating curve

catalog part 6, page 27)

–

15 A (10 ms)

––

2-conductor floating

2-conductor floating

polarity reversal protection and surge voltage protection

≤ 1 V

≤ 200 mV

General data

Test voltage input/output

Ambient temperature range

Duty type rating

Inflammability class

Standards/regulations

Installation position/assembly

Type of connection

2,5 kV, 50 Hz, 1 min.

– 20 °C to +60 °C

100 % ED

V0 in acc. with UL 94

IEC 664/IEC 664 A/DIN VDE 0110,

contamination class 2, surge voltage protection category III,

as desired, in rows with zero spacing

spring cage connection

terminal blocks of adjacent modules, the PLC-ATP separating plate

(see catalog part 6, page 34) should be installed.

Notes:

Type of housing: polyamide PA non-reinforced,

Color: green, see catalog part 6, page 149

Marking systems and mounting material, see catalog part 3/4.

The rated cross section (see catalog part 6, page 151) refers to

untreated conductors without ferrules.

For the protection of input and output, inductive loads must be

dampened with an effective protection circuit.

Due to the input circuit integrated in the base terminal block (see

catalog part 6, page 33), a 60 V optical coupler, OTP-60DC/…, is

used with the 120 V and 230 V modules.

The PLC-ATP separating plate must always be installed at the

beginning and end of a PLC terminal strip.

For protective isolation between identical terminal blocks of

adjacent modules, the PLC-ATP separating plate (see catalog part

6, page 34) should be installed.

PLC Sensor Interface with Optical Coupler

– now also with spring cage connection system!

PHOENIX CONTACT page 12 of 14