ADL5330ACPZ-R2 datasheet(15/24 Pages) AD

15 / 24 page

Data Sheet

ADL5330

Rev. B | Page 15 of 24

GAIN CONTROL INPUT

When the VGA is enabled, the voltage applied to the GAIN pin

sets the gain. The input impedance of the GAIN pin is 1 MΩ.

The gain control voltage range is between 0 V and +1.4 V, which

corresponds to a typical gain range between −38 dB and +22 dB.

The useful lower limit of the gain control voltage increases at

high frequencies to about 0.5 V and 0.6 V for 2.2 GHz and

2.7 GHz, respectively. The supply current to the ADL5330 can

vary from approximately 100 mA at low gain control voltages to

215 mA at 1.4 V.

The 1 dB input compression point remains constant at 3 dBm

through the majority of the gain control range, as shown in

Figure 9 through Figure 13. The output compression point

increases dB for dB with increasing gain setting. The noise floor

is constant up to 1 V where it begins to rise.

The bandwidth on the gain control pin is approximately 3 MHz.

Figure 14 shows the response time of a pulse on the GAIN pin.

AUTOMATIC GAIN CONTROL

Although the ADL5330 provides accurate gain control, precise

regulation of output power can be achieved with an automatic

gain control (AGC) loop. Figure 36 shows the ADL5330 in an

AGC loop. The addition of the log amp (AD8318/AD8315) or a

TruPwr™ detector (AD8362) allows the AGC to have improved

temperature stability over a wide output power control range.

To operate the ADL5330 in an AGC loop, a sample of the output

RF must be fed back to the detector (typically using a directional

coupler and additional attenuation). A setpoint voltage is applied

to the VSET input of the detector while VOUT is connected to

the GAIN pin of the ADL5330. Based on the defined linear in dB

relationship of the detector between VOUT and the RF input

signal, the detector adjusts the voltage on the GAIN pin (the

VOUT pin of the detector is an error amplifier output) until the

level at the RF input corresponds to the applied setpoint voltage.

The GAIN setting settles to a value that results in the correct

balance between the input signal level at the detector and the

setpoint voltage.

The error amplifier of the detector uses CFLT, a ground referenced

capacitor pin, to integrate the error signal (in the form of a

current). A capacitor must be connected to CFLT to set the loop

bandwidth and to ensure loop stability.

INLO

INHI

GAIN

OPLO

OPHI

DIRECTIONAL

COUPLER

ATTENUATOR

VPOS

COMM

ADL5330

+5V

CLPF

VOUT

VSET

RFIN

LOG AMP OR

TRUPWR

DETECTOR

DAC

RFIN

Figure 36. ADL5330 in AGC Loop

The basic connections for operating the ADL5330 in an AGC

loop with the AD8318 are shown in Figure 37. The AD8318 is a

1 MHz to 8 GHz precision demodulating logarithmic amplifier.

It offers a large detection range of 60 dB with ±0.5 dB tempera-

ture stability. This configuration is similar to Figure 36.

The gain of the ADL5330 is controlled by the output pin of the

AD8318. This voltage, VOUT, has a range of 0 V to near VPOS.

To avoid overdrive recovery issues, the AD8318 output voltage

can be scaled down using a resistive divider to interface with the

0 V to 1.4 V gain control range of ADL5330.

A coupler/attenuation of 23 dB is used to match the desired

maximum output power from the VGA to the top end of the

linear operating range of the AD8318 (at approximately −5 dBm

at 900 MHz).

ADL5330ACPZ-R2 数据表(PDF) 15 Page - Analog Devices

ADL5330ACPZ-R2 数据表(HTML) 15 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载