HT95L00P datasheet(8/52 Pages) HOLTEK

8 / 52 page

Symbol

Parameter

Test Conditions

Min.

Typ.

Max.

Unit

VDD

Conditions

DTMF Generator

VTDC

DTMF Output DC Level

¾¾

0.45VDD

0.7VDD

VTOL

DTMF Sink Current

¾ VDTMF=0.5V

0.1

¾¾

VTAC

DTMF Output AC Level

¾ Row group, RL=5kW

120

155

180

mVrms

DTMF Output Load

¾ THD£-23dB

¾¾

ACR

Column Pre-emphasis

¾ Row group=0dB

THD

Tone Signal Distortion

¾ RL=5kW¾

-30

-23

HT95LXXX

Rev. 1.20

May 26, 2004

Functional Description

Execution Flow

The system clock for the telephone controller is derived

from a 32768Hz crystal oscillator. A built-in frequency up

conversion circuit provides dual system clock, namely;

32768Hz and 3.58MHz. The system clock is internally

divided into four non-overlapping clocks. One instruc-

tion cycle consists of four system clock cycles. Instruc-

tion fetching and execution are pipelined in such a way

that a fetch takes an instruction cycle while decoding

and execution takes the next instruction cycle. The

pipelining scheme causes each instruction to be effec-

tively executed in a instruction cycle. If an instruction

changes the program counter, two instruction cycles are

required to complete the instruction.

Program Counter

- PC

The program counter (PC) controls the sequence in

which the instructions stored in the program ROM are

executed and its contents specify a full range of pro-

gram memory. After accessing a program memory word

to fetch an instruction code, the contents of the program

counter are incremented by 1. The program counter

then points to the memory word containing the next in-

struction code.

When executing a jump instruction, conditional skip ex-

ecution, loading PCL register, subroutine call, initial re-

set, internal interrupt, external interrupt or return from

subroutine, the program counter manipulates the pro-

gram transfer by loading the address corresponding to

each instruction. The conditional skip is activated by

instructions. Once the condition is met, the next instruc-

tion, fetched during the current instruction execution, is

discarded and a dummy cycle replaces it to get the

proper instruction. Otherwise proceed to the next in-

struction.

The program counter lower order byte register

(PCL:06H) is a readable and write-able register. Moving

data into the PCL performs a short jump. The destina-

tion will be within 256 locations. When a control transfer

takes place, an additional dummy cycle is required.

Program Memory

- ROM

The program memory is used to store the program in-

structions which are to be executed. It also contains

data, table, and interrupt entries, and is organized into

´16 bits´2 banks (HT95L400/40P), 8K´16 bits

(HT95L300/30P, HT95L200/20P) or 4K

´16 bits

(HT95L100/10P, HT95L000/00P), addressed by the

program counter and table pointer.

For the HT95L400/40P, the program memory is divided

into 2 banks, each bank having a ROM Size 8K

´16 bits.

To move from the present ROM bank to a different ROM

bank, the higher 1 bits of the ROM address are set by

the BP (Bank Pointer), while the remaining 13 bits of the

PC are set in the usual way by executing the appropriate

jump or call instruction. As the 14 address bits are

latched during the execution of a call or jump instruction,

the correct value of the BP must first be setup before a

T 1

T 2

T 3

T 4

T 1

T 2

T 3

T 4

T 1

T 2

T 3

T 4

F e t c h I N S T ( P C )

E x e c u t e I N S T ( P C - 1 )

F e t c h I N S T ( P C + 1 )

E x e c u t e I N S T ( P C )

F e t c h I N S T ( P C + 2 )

E x e c u t e I N S T ( P C + 1 )

P C

P C + 1

P C + 2

S y s t e m C l o c k

P C

Execution Flow

HT95L00P 数据表(PDF) 8 Page - Holtek Semiconductor Inc

HT95L00P 数据表(HTML) 8 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载