AX88178 datasheet(5/35 Pages) ASIX

5 / 35 page

ASIX ELECTRONICS CORPORATION

AX88178 L

USB to 10/100/1000 Gigabit Ethernet/HomePNA Controller

2.0 Signal Description

The following abbreviations apply to the following pin description table.

Input, 2.5V with 3.3V tolerant

Bi-directional I/O, 2.5V with 3.3V tolerant

Input, 3.3V

Bi-directional I/O, 3.3V with 5V tolerant

Input, 3.3V with 5V tolerant

Internal Pull Up (75K)

Output, 2.5V with 3.3V tolerant

Internal Pull Down (75K)

Output, 3.3V

Power Pin

Output, 3.3V with 5V tolerant

Schmitt Trigger

Bi-directional I/O

Table 1: Pinout Descripton

Pin Name

Type

Pin No

Pin Description

USB Interface

USB 2.0 data positive pin.

USB 2.0 data negative pin.

DPRS

USB 1.1 data positive pin. Please connect to DP through a 39ohm

(+/-1%) serial resistor.

DMRS

USB 1.1 data negative pin. Please connect to DM through a 39ohm

(+/-1%) serial resistor.

VBUS

I5/PD/S

VBUS pin input. Please connect to USB bus power.

XIN12M

12Mhz crystal or oscillator clock input. This clock is needed for USB

PHY transceiver to operate.

XOUT12M

12Mhz crystal or oscillator clock output.

RREF

For USB PHY’s internal biasing. Please connect to AGND through a

12.1Kohm (+/-1%) resistor.

RPU

For USB PHY’s internal biasing. Please connect to AVDD3 (3.3V)

through a 1.5Kohm (+/-5%) resistor.

Station Management Interface

MDC

121

Station Management Data Clock output. The timing reference for

MDIO. All data transfers on MDIO are synchronized to the rising edge

of this clock. The frequency of MDC is 1.5MHz.

MDIO

B2/PU

120

Station Management Data Input/Output. Serial data input/output

transfers from/to the PHYs. The transfer protocol conforms to the

IEEE 802.3u MII spec.

MDINT

I2/PU

117

Station Management Interrupt input.

MII/GMII/RGMII Interface

RX_CLK

104

Receive Clock. RX_CLK is received from PHY to provide timing

reference for the transfer of RXD [7:0], RX_DV, and RX_ER signals

on receive direction of MII/GMII/RGMII interface.

RXD [7:0]

114, 113,

112, 111,

110, 109,

108, 107

Receive Data. RXD [7:0] is driven synchronously with respect to

RX_CLK by PHY. In RGMII mode, only RXD [3:0] is used.

RX_DV

105

Receive Data Valid. RX_DV is driven synchronously with respect to

RX_CLK by PHY. It is asserted high when valid data is present on

RXD [7:0]. In RGMII mode, RX_DV acts as RX_CTL.

RX_ER

106

Receive Error. RX_ER is driven synchronously with respect to

RX_CLK by PHY. It is asserted high for one or more RX_CLK

periods to indicate to the MAC that an error has detected.

COL

116

Collision Detected. COL is driven high by PHY when the collision is

detected.

CRS

115

Carrier Sense. CRS is asserted high asynchronously by the PHY when

either transmit or receive medium is non-idle.

AX88178 数据表(PDF) 5 Page - ASIX Electronics Corporation

AX88178 数据表(HTML) 5 Page - ASIX Electronics Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

数据表下载