ST7LITE30 datasheet(100/167 Pages) STMICROELECTRONICS

100 / 167 page

ST7LITE3

100/167

LINSCI

™ SERIAL COMMUNICATION INTERFACE (SCI Mode) (Cont’d)

CONTROL REGISTER 2 (SCICR2)

Read/Write

Reset Value: 0000 0000 (00h)

1)This bit has a different function in LIN mode, please

refer to the LIN mode register description.

Bit 7 = TIE Transmitter interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: In SCI interrupt is generated whenever TDRE=1

in the SCISR register

Bit 6 = TCIE Transmission complete interrupt ena-

ble

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever TC=1 in

the SCISR register

Bit 5 = RIE Receiver interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever OR=1

or RDRF=1 in the SCISR register

Bit 4 = ILIE Idle line interrupt enable.

This bit is set and cleared by software.

0: Interrupt is inhibited

1: An SCI interrupt is generated whenever IDLE=1

in the SCISR register.

Bit 3 = TE Transmitter enable.

This bit enables the transmitter. It is set and

cleared by software.

0: Transmitter is disabled

1: Transmitter is enabled

Notes:

– During transmission, a “0” pulse on the TE bit

(“0” followed by “1”) sends a preamble (idle line)

after the current word.

– When TE is set there is a 1 bit-time delay before

the transmission starts.

Bit 2 = RE Receiver enable.

This bit enables the receiver. It is set and cleared

by software.

0: Receiver is disabled in the SCISR register

1: Receiver is enabled and begins searching for a

start bit

Bit 1 = RWU Receiver wake-up.

This bit determines if the SCI is in mute mode or

not. It is set and cleared by software and can be

cleared by hardware when a wake-up sequence is

recognized.

0: Receiver in active mode

1: Receiver in mute mode

Notes:

– Before selecting Mute mode (by setting the RWU

bit) the SCI must first receive a data byte, other-

wise it cannot function in Mute mode with wake-

up by Idle line detection.

– In Address Mark Detection Wake-Up configura-

tion (WAKE bit=1) the RWU bit cannot be modi-

fied by software while the RDRF bit is set.

Bit 0 = SBK Send break.

This bit set is used to send break characters. It is

set and cleared by software.

0: No break character is transmitted

1: Break characters are transmitted

Note: If the SBK bit is set to “1” and then to “0”, the

transmitter will send a BREAK word at the end of

the current word.

DATA REGISTER (SCIDR)

Read/Write

Reset Value: Undefined

Contains the Received or Transmitted data char-

acter, depending on whether it is read from or writ-

ten to.

The Data register performs a double function (read

and write) since it is composed of two registers,

one for transmission (TDR) and one for reception

(RDR).

The TDR register provides the parallel interface

between the internal bus and the output shift reg-

ister (see Figure 54).

The RDR register provides the parallel interface

between the input shift register and the internal

bus (see Figure 54).

TIE

TCIE

RIE

ILIE

RWU

SBK1)

DR7

DR6

DR5

DR4

DR3

DR2

DR1

DR0

ST7LITE30 数据表(PDF) 100 Page - STMicroelectronics

ST7LITE30 数据表(HTML) 100 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7LITE30 数据表(PDF) 100 Page - STMicroelectronics

ST7LITE30 数据表(HTML) 100 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载