MODEL: JPR2

JPR2 SPECIFICATIONS

ES-1580 Rev.10 Page 2/7

http://www.m-system.co.jp/

/S01: Stainless steel

CAUTION

1) The JPR2 is not designed to output uniform pulses even

when the input wave is uniform. It is not applicable to

certain types of application.

2) The JPR2 converts the pulse counts, not frequency. For

the frequency conversion purpose, model JFR2 is

recommended.

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input or sensor exc. to output to power

Input monitor LED: Red LED blinks according to the input.

Excitation adjustment: 5 – 24 V DC

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Input and output pulse set count (frequency)

• Sampling time

• Input pulse edge

• Max. frequency limit

• Others

Adjustments: With DIP and Rotary switches.

• Pulse amplitude

• Input type

• Noise filter

(Refer to the instruction manual for details)

Sampling time: 0.01 – 100 sec.

Buffer counter capacity: 4 294 967 295 counts

Input pulse sensing: DC coupled

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; approx. 440 mA (max.) at

shortcircuit

Max. frequency: 100 kHz

(10 Hz for mechanical contact input)

Minimum pulse width time requirement: 5 μsec.; 50 msec.

for mechanical contact (for both ON and OFF)

■ Open Collector & Mechanical Contact

Input requirements (Excitation: Sensing)

5 V: Approx. 4 V / 1.0 mA

12 V: Approx. 9 V / 2.3 mA

24 V: Approx. 16 V / 4.7 mA

Resistance at ON : ≤ 200 Ω

Resistance at OFF : ≥ 200 kΩ

Detecting level: 1 V with 5 V excitation

2 V with 12 V/24 V excitation.

(Detecting voltage in the internal circuit)

For open collector or mechanical contact input, be sure to re

-adjust the voltage back to 1 V (excitation 5 V) or 2 V

(excitation 12 V/24 V) if it has been changed for other input

types.

Detecting pulse edge: OFF (input monitor LED ON) to ON

(input monitor LED OFF) or ON to OFF

■ Voltage Pulse

Waveform: Square or sine

Input impedance: ≥ 10 kΩ

Pulse amplitude: 0.1 – 100 Vp-p (square)

1 – 100 Vp-p (sine or similar)

Max. voltage between input terminals: 50 V

Detecting level: 0 – 5 V (Detecting voltage in the internal

circuit.)

Detecting pulse state: A pulse rise detected when the input

voltage goes above the detecting level (input monitor LED

ON); a pulse sink detected when it goes below the level

(input monitor LED OFF).

■ Two-wire Current Pulse

Input resistance: Receiving resistor 100 Ω

Input range: 0 – 25 mA

Minimum pulse amplitude: 10 mA

Detecting level: 0 – 5 V

(Detecting voltage in the internal circuit.)

Detecting pulse state: The input resistor (100 Ω) converts

the current signal (0 - 25 mA) into 0 – 2.5 V. A pulse rise

detected when the voltage goes above the detecting level

(input monitor LED ON); a pulse sink detected when it goes

below the level (input monitor LED OFF).

■ RS-422 Line Driver Pulse

Receiver: Conforms to RS-422

50V max.

Amplitude

Vinp-p

t

Volts

DC Offset

■ Voltage pulse waveform