MODEL: JPQ2

JPQ2 SPECIFICATIONS

ES-1579 Rev.9 Page 2/5

http://www.m-system.co.jp/

S: 12 V DC

R: 24 V DC

V: 48 V DC

P: 110 V DC

[4] OPTIONS

blank: none

/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q (multiple selections)

COATING (For the detail, refer to M-System's web site.)

/C01: Silicone coating

/C02: Polyurethane coating

/C03: Rubber coating

TERMINAL SCREW MATERIAL

/S01: Stainless steel

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to DC output to alarm output to power

Overrange output: Approx. -15 to +115 % at 1 – 5 V

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Alarm mode: High

Alarm setpoint: -15 – +115 %

Linearization: Max. 16 points

Input monitor LED: Red LED blinks according to the input.

Excitation adjustment: 5 – 24 V DC

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Zero and span

• Linearization

• Alarm setpoint

• Output fine adjustment

• Others

Adjustments: With DIP and Rotary switches.

• Pulse amplitude

• Input type

• Noise filter

(Refer to the instruction manual for details)

Modular jack: Connecting the PU-2x

Input pulse sensing: DC coupled

Reset input: Resets the internal counter value (The

transmitter output equivalent to 0 count when the reset

input terminals are closed for 500 msec. or longer.)

Output at count overflow: Reset (restart at 0 count), Hold at

100 % count or 115 % count

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; approx. 440 mA (max.) at

shortcircuit

Maximum frequency: 100 kHz

(10 Hz for mechanical contact)

Maximum count range: 0 to 99999999

Minimum pulse width time requirement: 5 μsec.; 50 msec.

for mechanical contact

(for both ON and OFF)

■ Open Collector & Mechanical Contact

Input requirements

(Excitation: Sensing)

5 V: Approx. 4 V / 1.0 mA

12 V: Approx. 9 V / 2.3 mA

24 V: Approx. 16 V / 4.7 mA

ON resistance: ≤ 200 Ω

OFF resistance: ≥ 200 kΩ

Detecting level: 2 V (Detecting voltage in the internal

circuit.)

Detecting pulse edge: OFF (input monitor LED ON) to ON

(input monitor LED OFF) or ON to OFF

■ Voltage Pulse

Waveform: Square or sine

Input impedance: 10 kΩ min.

Pulse amplitude: 0.1 – 100 V p-p (1 – 100 Vp-p for sine or

similar waveforms)

Max. voltage between input terminals: 50 V

Detecting level: 0 – 5 V (factory setting: 2 V)

Detecting voltage in the internal circuit.

Detecting pulse state: A pulse rise detected when the input

voltage goes above the detecting level (input monitor LED

ON); a pulse sink detected when it goes below the level

(input monitor LED OFF).

■ Two-wire Current Pulse

Input resistance: Receiving resistor 100 Ω

Input range: 0 – 25 mA

Minimum pulse amplitude: 10 mA

Detecting level: 0 – 5 V

(Detecting voltage in the internal circuit.)

Detecting pulse state: The input resistor (100 Ω) converts