MODEL: MXR

MXR SPECIFICATIONS

ES-1714 Rev.11 Page 2/3

http://www.m-system.co.jp/

INPUT SPECIFICATIONS

Maximum leadwire resistance: 200 Ω per wire (3-wire)

Sensing current: ≤ 0.5 mA

Input min. step: 0.1 ('1' for ≥ ±1000)

Default setting: Pt 100 (JIS '97, IEC) 0 – 100°C

Temperature range

RTD

USABLE RANGE

°C

°F

JPt 100 (JIS ’89)

Pt 100 (JIS ’89)

Pt 100 (JIS ’97, IEC)

-230

-230

-230

to

to

to

+560

+900

+900

-382

-382

-382

to

to

to

+1040

+1652

+1652

Pt 50Ω (JIS ’81)

Ni 508.4Ω

Pt 1000

-230

-100

-230

to

to

to

+700

+330

+900

-382

-148

-382

to

to

to

+1292

+626

+1652

Ni 100

Cu 10Ω @25°C

-100

-210

to

to

+250

+310

-148

-346

to

to

+482

+590

Note 1: Set the upper range temperature with a larger value

than the lower range termperature value.

Note 2: Inverted output is available with the configuration.

Note 3: Operational range is of -15 to +115% or in the usable

range as indicated above.

OUTPUT SPECIFICATIONS

■ DC Current: 0.0 – 20.0 mA DC

Operational range: 0.0 – 24.0 mA DC

Minimum increment: 0.1 mA

Default setting: 4.0 – 20.0 mA DC

■ DC Voltage

Code V1: -1.00 – +1.00 V DC

Operational range: -1.15 – +1.15 V DC

Minimum increment: 10 mV

Code V2: -10.0 – +10.0 V DC

Operational range: -11.5 – +11.5 V DC

Minimum increment: 100 mV

Note: Set to the 100 % output with a larger value than the

0 % output value.

Default setting:

Code V1: -1.00 – +1.00 V DC

Code V2: -10.0 – +10.0 V DC

INSTALLATION

Power consumption

•AC:

Approx. 4 VA at 100 V

Approx. 5 VA at 200 V

Approx. 6 VA at 264 V

•DC: Approx. 3.5 W (100 mA at 24 V)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 280 g (0.62 lb)

PERFORMANCE

Accuracy: Input + output

Input: ±0.3°C (±0.54°F) typical

±0.5°C (±0.9°F) for Cu 10

Output: ±0.05 %

Min. span required to ensure the accuracy:

20% of the nominal I/O range

Display accuracy: Input accuracy ±1 digit

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)

Response time: ≤ 0.5 sec. (0 – 90 %)

Burnout response time: ≤ 2 sec.

Line voltage effect: ±0.1 % over voltage range

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (input to output

to power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input or output to power: Reinforced insulation (300 V)

Input to output: Basic insulation (300 V)

RoHS Directive

EN 50581