AD10201SLASHPCB datasheet(3/20 Pages) AD

3 / 20 page

REV. 0

–3–

AD10201

Test

Parameter

Temp

Level

Min

Typ

Max

Unit

DYNAMIC PERFORMANCE

Signal-to-Noise Ratio (SNR)

8 (Without Harmonics)

fIN = 10 MHz

°CI

dBFS

fIN = 41 MHz

°CV

dBFS

fIN = 71 MHz

°CI

63.5

66.5

dBFS

fIN = 121 MHz

°CV

dBFS

Signal-to-Noise Ratio (SINAD)

9 (With Harmonics)

fIN = 10 MHz

°CI

65.5

67.5

dBFS

fIN = 41 MHz

°CV

67.2

dBFS

fIN = 71 MHz

°CI

dBFS

fIN = 121 MHz

°CV

dBFS

Spurious-Free Dynamic Range

fIN = 10 MHz

°CI

75.5

dBFS

fIN = 41 MHz

°CV

dBFS

fIN = 71 MHz

°CI

dBFS

fIN = 121 MHz

°CV

dBFS

Two-Tone Intermodulation

Distortion

11 (IMD)

fIN = 10 MHz; fIN = 12 MHz

°CV

dBc

fIN = 71 MHz; fIN = 72 MHz

°CV

dBc

fIN = 121 MHz; fIN = 122 MHz

°CV

dBc

Channel-to-Channel Isolation

fIN = 121 MHz

Full

dBc

NOTES

1 All specifications tested by driving ENCODE and

ENCODE differentially, with the analog input applied to A

INX1 and AINX2 tied to ground.

2 Gain error measured at 10.3 MHz.

3 Input VSWR, see TPC 12.

4 See Figure 1, Timing Diagram.

5 t

V and tPD are measured from the transition points of the ENCODE input to the 50%/50% levels of the digital outputs swing. The digital output load during test is

not to exceed an ac load of 10 pF or a dc current of

±40 A.

6 Supply voltages should remain stable within

±5% for normal operation.

7 Power dissipation measures with encode at rated speed.

8 Analog input signal power at –1 dBFS; signal-to-noise (SNR) is the ratio of signal level to total noise (first six harmonics removed).

ENCODE = 105 MSPS. SNR is reported in dBFS, related back to converter full scale.

9 Analog input signal power at –1 dBFS; signal-to-noise and distortion (SINAD) is the ratio of signal level to total noise + harmonics. ENCODE = 105 MSPS.

SINAD is reported in dBFS, related back to converter full scale.

10Analog input signal equals –1 dBFS; SFDR is ratio of converter full scale to worst spur.

11Both input tones at –7 dBFS; two-tone intermodulation distortion (IMD) rejection is the ratio of either tone to the worst third order intermod product.

12Channel-to-channel isolation tested with A channel/50

Ω terminated (A

IN A2 grounded) and a full-scale signal applied to B channel (A IN B2).

Specifications subject to change without notice.

AD10201/PCB 数据表(PDF) 3 Page - Analog Devices

AD10201/PCB 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表下载

链接网址

AD10201/PCB 数据表(PDF) 3 Page - Analog Devices

AD10201/PCB 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表 下载

链接网址

数据表下载