MODEL: SC200

SC200 SPECIFICATIONS

ES-6338 Rev.17 Page 4/12

http://www.m-system.co.jp/

ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ

■ Pi6: Dry contact

(Di6 is assigned to the same terminal.)

Maximum frequency: 10 kHz

Minimum pulse width: 0.05 msec.

Common: Negative common

Sensing: Approx. 12 V DC, 12 mA

ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ

Excitation: 12 V DC ±10%, 15 mA

Current limiting circuit: Approx. 30 mA

■ Di1, Di2, Di3, Di4, Di5: Dry contact

(Pi1 through Pi5 are assigned to the same terminals

respectively.)

Common: Negative common per 5 points

Sensing: Approx. 12 V DC, 6 mA

ON voltage/resistance: ≤ 2.25 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11.25 V ≥ 15 kΩ

■ Di6: Dry contact

(Pi6 is assigned to the same terminal.)

Common: Negative common

Sensing: Approx. 12 V DC, 12 mA

ON voltage/resistance: ≤ 2 V, ≤ 1.5 kΩ

OFF voltage/resistance: ≥ 11 V, ≥ 15 kΩ

[Table 1 (Thermocouple input)]

T/C

USABLE

RANGE (°C)

CONFORMANCE

RANGE (°C)

K (CA)

-272 to +1472

-150 to +1370

E (CRC)

-272 to +1100

-170 to +1000

J (IC)

-260 to +1300

-180 to +1200

T (CC)

-272 to

+500

-170 to +400

B (RH)

24 to

1920

1000 to 1760

R

-100 to +1860

380 to 1760

S

-100 to +1860

400 to 1760

C (WRe 5-26)

-52 to +2416

100 to 2315

N

-272 to +1400

-130 to +1300

U

-252 to

+700

-200 to +600

L

-252 to +1000

-200 to +900

P (Platinel II)

-52 to +1496

0 to 1395

(PR)

-52 to +1860

300 to 1760

Overrange input (out of the usable range) is handled as burnout.

[Table 2 (RTD input)]

RTD

USABLE

RANGE (°C)

CONFORMANCE

RANGE (°C)

Pt 100 (JIS ’97, IEC)

-240 to +900

-200 to +850

Pt 100 (JIS ’89)

-240 to +900

-200 to +660

JPt 100 (JIS ’89)

-236 to +560

-200 to +510

Pt 50Ω (JIS ’81)

-236 to +700

-200 to +649

Ni 100

-100 to +252

-80 to +250

Overrange input (out of the usable range) is handled as burnout.

OUTPUT SPECIFICATIONS

■ Mv1, Mv2

∙Current output: 4 – 20 mA DC

Load resistance: ≤ 600 Ω

■ Ao1, Ao2

∙Voltage output: 1 – 5 V DC

Load resistance: ≥ 10 kΩ

■ Discrete Output

∙Do1, Do2, Do3, Do4, Do5, RUN contact (Do6): Relay

contact

Rated load: 250 V AC @1 A (cos ø = 1)

30 V DC @1 A (resistive load)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 250 VA or 60 W

Minimum load: 5 V DC @10 mA

∙Do1, Do2, Do3, Do4, Do5: Photo MOSFET relay

Rating: 200 V AC/DC @0.5 A (resistive load)

ON resistance: 2.1 Ω

Maximum frequency: 4 Hz @24 V, 10 mA

ON delay time: ≤ 5.0 msec.

OFF delay time: ≤ 3.0 msec.

INSTALLATION

Power input

∙AC:

≤ 25 VA at 100 V AC

≤ 40 VA at 240 V AC

•DC: ≤ 650 mA

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 5 to 90 %RH (non-condensing)

Mounting: Panel flush mounting (high-density mounting in

horizontal direction)

Weight:

Approx. 1.8 kg (3.97 lb) for 250 mm depth type

Approx. 2.0 kg (4.41 lb) for 300 mm depth type

Approx. 2.5 kg (5.51 lb) for 400 mm depth type

PERFORMANCE

Accuracy

DC input: ±0.1 % ±1 digit

Thermocouple input: ±1℃ ±1 digit

±2℃ ±1 digit for B, R, S, C and PR

RTD input: ±1℃ ±1 digit

Potentiometer input: ±0.2 % ±1 digit

DC output: ±0.1 %

Precision resistor module (REM4): ±0.1 %

Cold junction compensation:

±2°C at 25°C ±10°C

±4°C for S, R and PR

Temp. coefficient: ±0.015 %/°C (±0.008 %/°F)