MODEL: SC210

SC210 SPECIFICATIONS

ES-6340 Rev.18 Page 2/14

http://www.m-system.co.jp/

• Current output (4-20 mA) x 2 points, voltage output (1-5

V) x 2 points, relay or photo-MOSFET relay output x 5 points

• RUN contact output (relay) x 1 point

• I/O signals can be added with remote I/O modules

connected via NestBus peer-to-peer communication

• Computation cycle selectable between 50 msec. and 3

sec. (control cycle selectable between 1 and 64 times of the

computation cycle)

• Two PID function blocks

• Advanced computation and sequence control functions

• Auto-tuning function

• Parameter input and changing with touch panel

• Function parameter setting, list printing and data

downloading/uploading available with Loop Configuration

Builder Software (model: SFEW3E)

• Short trend export (CSV), display parameter setting,

saving and transfer with PC Configurator Software (model:

SCCFG)

• Control and supervision by SCADA software via Modbus

TCP/IP or RTU communication

• Backup module (applicable to Mv2 only) is incorporated

for manual loading: MV output is automatically switched to

manual control in case of control module abnormality

• Independent power supply usable for the manual loader

• Control module can be extracted at the front for

replacement while MV output is maintained

• Selectable housing depth for ease of using existing wires

in replacement: 300 mm and 400 mm

• Separable terminal block

Typical Applications

• Replacement of conventional controllers

• Panel operation for small-scale instrumentation

RELATED PRODUCTS

• PC Configurator cable (model: COP-US)

• Loop configuration builder software (model: SFEW3E Ver.

1.40 or later)

• Infrared communication adaptor (model: COP-IRDA)

• PC configurator software (model: SCCFG Ver.1.50 or later)

Builder software and configurator software are

downloadable at M-System’s web site.

ACCESSORIES

• Precision resistor module (model: REM4): 2

• Cold junction sensor: 2

• Mounting brackets: 2

• Connector adapter: 1

(included in Stereo jack type. The jack on the unit and the

plug of PC Configurator cable (not included in the product)

are different in size.)

GENERAL SPECIFICATIONS

Construction: Panel flush mounting

Degree of protection: IP55; ensured for the front panel of

the unit independently mounted to a panel

Connection

Terminal screws: M3.5 screw terminals (torque 1.0 N·m)

Terminal fixing screws: M4 screw terminals

(torque 1.2 N·m)

Backup module power supply terminal (option /M2, /R):

Euro terminal block (applicable wire size: dia. 2.4 max.,

Ethernet: RJ-45 Modular Jack

Screw terminal

Terminal screws: Nickel-plated steel (standard) or stainless

steel

Terminal fixing screws: Chrome-plated steel

Housing material: Flame-resistant resin (gray), steel

Isolation: Pv1 to Pv2 to supply output to Ai1 or Ai2 or Ai3 or

Ai4 to Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or

Pi4 or Pi5 to Di6 or Pi6 to Mv1 to Mv2 or Mv2B to Ao1 or Ao2

to Do1 to Do2 to Do3 to Do4 to Do5 to Do6 to NestBus to

Modbus-RTU to Modbus/TCP to power to backup module

power to FG

PID control: Single loop, cascade, advanced

Proportional band (P): 1 to 1000 %

Integral time (I): 0.01 to 100 minutes

Derivative time (D): 0.01 to 10 minutes

Auto-tuning: Limit cycle method

Alarm: PV high & low, deviation, rate of change

Computation: 48 functions blocks available for arithmetic

operations, time functions, signal selection, limit, alarm and

other functions

Sequence operation: Logic sequence and step sequence

(max. 1068 commands)

Computation cycle: 50 msec. to 3 sec. (control cycle

selectable among 1, 2, 4, 8, 16, 32 and 64 times of the

computation cycle)

MV output range: -15 - +115 %

Parameter setting: With touch panel or PC (Loop

Configuration Builder Software model: SFEW3E)

Self diagnostics: CPU monitoring with a watchdog timer

RUN contact: OFF in error detected by diagnostic (including

NestBus)

Infrared communication: Transmission distance max. 0.2

meter (for use with the COP-IRDA)

Short trend

Storing interval: 1, 2, 5, 10, 20, 30 sec.,

1, 2, 5, 10, 30, 60 min.

Capacity: 400 points (display 200 points)

■ Display

Display device: 4.3-inch TFT LCD