

2021 Microchip Technology Inc.

DS00003852A-page 45

9.0

OPERATIONAL CHARACTERISTICS

9.1

Absolute Maximum Ratings*

Digital Core Supply Voltage (

VCORE) (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to +1.21 V

+3.3 V Supply Voltage (

VDD33) (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to +4.6 V

Positive voltage on input signal pins, with respect to ground (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6 V

Negative voltage on input signal pins, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V

Positive voltage on

XTALI/CLK_IN, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+3.63 V

Positive voltage on USB DP/DM signal pins, with respect to ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+6.0 V

Positive voltage on USB 3.2 Gen 2

USB3UP_xxxx and USB3DN_xxxx signal pins, with respect to ground . . . . .1.21 V

Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020

HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/-3.5 kV

Note 1: When powering this device from laboratory or system power supplies, it is important that the absolute max-

imum ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on

their outputs when AC power is switched on or off. In addition, voltage transients on the AC power line may

appear on the DC output. If this possibility exists, it is suggested that a clamp circuit be used.

Note 2: This rating does not apply to the following pins: All USB DM/DP pins, XTAL1/CLK_IN, XTALO and

VBUS_MON_UP.

*Stresses exceeding those listed in this section could cause permanent damage to the device. This is a stress rating

only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Functional

operation of the device at any condition exceeding those indicated in Section 9.2, Operating Conditions**, Section 9.5,

DC Specifications, or any other applicable section of this specification is not implied.

9.2

Operating Conditions**

Digital Core Supply Voltage (

VCORE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.09 V to +1.21 V

+3.3 V Supply Voltage (

VDD33) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.0 V to +3.6 V

Input Signal Pins Voltage (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +3.6 V

XTALI/CLK_IN Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +3.6 V

USB 2.0 DP/DM Signal Pins Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +5.5 V

USB 3.2 Gen 2

USB3UP_xxxx and USB3DN_xxxx Signal Pins Voltage . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +1.21 V

is guaranteed only within the ranges specified in this section. Do not drive input signals without power sup-

plied to the device.