ADP7112ACBZ-2.5-R7 datasheet(5/21 Pages) AD

5 / 21 page

Data Sheet

ADP7112

Rev. D | Page 5 of 21

ABSOLUTE MAXIMUM RATINGS

Table 3.

Parameter

Rating

VIN to GND

−0.3 V to +24 V

VOUT to GND

−0.3 V to VIN

EN to GND

−0.3 V to +24 V

SENSE/ADJ to GND

−0.3 V to +6 V

SS to GND

−0.3 V to VIN or +6 V

(whichever is less)

Storage Temperature Range

−65°C to +150°C

Operating Junction Temperature

(TJ) Range

−40°C to +125°C

Operating Ambient Temperature

(TA) Range

−40°C to +85°C

Soldering Conditions

JEDEC J-STD-020

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the

operational section of this specification is not implied.

Operation beyond the maximum operating conditions for

extended periods may affect product reliability.

THERMAL DATA

Absolute maximum ratings apply individually only, not in

combination. The ADP7112 can be damaged when the junction

temperature limits are exceeded. Monitoring ambient temperature

does not guarantee that TJ is within the specified temperature

limits. In applications with high power dissipation and poor

thermal resistance, the maximum ambient temperature can

have to be derated.

In applications with moderate power dissipation and low

printed circuit board (PCB) thermal resistance, the maximum

ambient temperature can exceed the maximum limit as long as

the junction temperature is within specification limits. The

junction temperature of the device is dependent on the ambient

temperature, the power dissipation (PD) of the device, and the

junction-to-ambient thermal resistance of the package (θJA).

Maximum TJ is calculated from the TA and PD using the

formula

TJ = TA + (PD × θJA)

(1)

θJA of the package is based on modeling and calculation using a

4-layer board. The θJA is highly dependent on the application

and board layout. In applications where high maximum power

dissipation exists, close attention to thermal board design is

required. The value of θJA can vary, depending on PCB material,

layout, and environmental conditions. The specified values of θJA

are based on a 4-layer, 4 in. × 3 in. circuit board. See JESD51-7 and

JESD51-9 for detailed information on the board construction.

ΨJB is the junction-to-board thermal characterization parameter

with units of °C/W. The ΨJB of the package is based on

modeling and calculation using a 4-layer board. The JESD51-12,

Guidelines for Reporting and Using Electronic Package Thermal

Information, states that thermal characterization parameters are

not the same as thermal resistances. ΨJB measures the component

power flowing through multiple thermal paths rather than a

single path as in thermal resistance (θJB). Therefore, ΨJB thermal

paths include convection from the top of the package as well as

radiation from the package, factors that make ΨJB more useful in

real-world app-lications. Maximum TJ is calculated from the

board temperature (TB) and PD using the formula

TJ = TB + (PD × ΨJB)

(2)

See JESD51-8 and JESD51-12 for more detailed information

about ΨJB.

THERMAL RESISTANCE

θJA, θJC, and ΨJB are specified for the worst-case conditions, that

is, a device soldered in a circuit board for surface-mount

packages.

Table 4. Thermal Resistance

Package Type

θJA

θJC

ΨJB

Unit

6-Ball WLCSP

260

°C/W

ESD CAUTION

ADP7112ACBZ-2.5-R7 数据表(PDF) 5 Page - Analog Devices

ADP7112ACBZ-2.5-R7 数据表(HTML) 5 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

数据表下载