| 数据搜索系统,热门电子元器件搜索 |
|
CF9501A 数据表(PDF) 5 Page - Nippon Precision Circuits Inc |
|
|
|||||||||||||||||||||||||||||
CF9501A 数据表(HTML) 5 Page - Nippon Precision Circuits Inc |
|
5 / 10 page ![]() SM9501A/B NIPPON PRECISION CIRCUITS INC.—5 Electrical Characteristics 9501A version VDD = 2.4 to 3.6V, VSS = 0V, Ta = −20 to +70°C unless otherwise noted. Parameter Symbol Condition Rating Unit min typ max Minimum operating voltage VMIN – – 2.4 V Maximum operating voltage VMAX 3.6 – – V Maximum operating current consumption1 1. Measured using the standard circuit. IDDM VDD = 3.0V, no input signal, PON: VSS, OUT: OPEN – 65 100 µA Operating current consumption1 IDDT VDD = 3.0V, 500ms pulsewidth, 0.1mVrms input (differential input), PON: VSS, OUT: OPEN –55– µA Standby mode current consumption IST PON, FCN, HLDN: VDD or OPEN – – 0.1 µA Minimum input voltage range VFMIN IN1–IN2 differential input – 0.5 1.0 µVrms Maximum input voltage range VFMAX IN1–IN2 differential input 80 – – mVrms Input frequency FIN IN1–IN2 differential input 35 – 80 kHz Analog switch resistance RA V|IN2–IN3| = 50mV, VIN2 = 0V – – 15 Ω Startup time2 2. The time taken under stable wave input conditions from when power is applied or standby is released, using PON, until stable digital output occurs within ratings. tON When supply is applied – – 8 sec Startup time2 (PON) tPON From standby mode – – 8 sec PON input current II1 VIN = 0V – – –1.5 µA FCN input current II2 VIN = 0V – – –1.5 µA HLDN input current II3 VIN = 0V – – –1.5 µA LOW-level output current IOL VDD = 2.4V, OUT = 0.5V 10 – – µA HIGH-level output current IOH VDD = 2.4V, OUT = 1.9V –10 – – µA Gain hold time tHLD ± 3dB change – – 1 sec Fall time output propagation delay3 3. The time taken, with 10:1 input signal amplitude ratio and 500ms pulsewidth, from when a change in signal input occurs until the output OUT changes. Note that this characteristic is very dependent on the antenna and crystal filter characteristics. The standard crystal used here has the following equiv- alent circuit coefficients. tDN FIN = 40/60kHz, standard crystal, NPC standard jig VIN = 1µVrms to 80mVrms – – 160 ms Rise time output propagation delay3 tUP – – 200 ms LOW-level output pulsewidth4 (200ms) 4. Values obtained when using the standard crystal employed here. Note that these values are dependent on the crystal characteristics, and should be considered as reference values. T200 100 200 300 ms LOW-level output pulsewidth4 (500ms) T500 400 500 650 ms LOW-level output pulsewidth4 (800ms) T800 700 800 900 ms Noise rejection ratio5 5. Time averaged rms values, where the noise is white noise and the measurement bandwidth is determined by the crystal filter equivalent used in the standard circuit. S/N ––9 dB f [kHz] L1 [kH] C1 [fF] R1 [k Ω]C0 [pF] 40 6.70280 2.36228 11.4492 1.42773 60 5.17396 1.36007 13.4826 1.04927 L1 C0 R1 C1 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |