H7CC-R11W datasheet(10/66 Pages) OMRON

10 / 66 page

H7CC-A

Nomenclature

(Default setting)

OFF

(Disable)

(Enable)

Operation Keys

10. Up Keys (UP1 to UP6)

14. Status indicator

11. Down Keys (DW1 to DW6)

12. Reset Operation (UP6+DW6)

Switches

· When the indicator display mode is ON

When used as a counter, the ratio of the present value to the set value is displayed from

0 to 100%.

When used as a tachometer, if "Upper and lower limit" or "Area" is selected in the

tachometer output mode, the ratio of the measurement value to the comparison value is

displayed from 0 to 100%.

· When the indicator display mode is all off or all lit

All off or all lit display.

Note. When you press the Up Key or the Down Key, the status indicator display goes off,

and the pressed key lights up or blinks.

· The keys that can be set light up for notification.

(The reset operation is enabled by pressing and holding the keys for 1 second or longer.

When the keys are pressed simultaneously, all status indicators start blinking. The reset

operation is disabled if the keys are released within 1 second.)

To perform the reset operation, firmly press and hold both UP6 and DW6. If you press only

UP6 or DW6, the set value will change.

13. Mode Operation (UP1+UP3 or DW1+DW3)

(Changes modes and setting items. Press and hold the keys for 2 seconds or longer to

move to the function setting mode. When the keys are pressed simultaneously, the status

indicators on UP1 (DW1) and UP3 (DW3) start blinking.

The mode operation is disabled if the keys are released within 2 seconds.)

(UP1, 2, 3, 4, 5, 6 from right to left)

(DW1, 2, 3, 4, 5, 6 from right to left)

Display Section

3. Reset Indicator (yellow)

1. Key Protect Indicator (yellow)

2. Control Output Indicator (yellow)

4. Total Count Indicator

6. Set Value 1, 2 Stage Indicator

8. Set value (Sub-display)

(Character height: 6 mm, green)

9. Hold Display (yellow)

OUT: (One-stage)

OUT:

(Two-stage)

(Lit when the total count value is displayed.)

(Lit when the reset input (1) is ON or

reset operation is performed.)

Displayed only when the configuration

selection mode is not tachometer mode.

5. Batch Indicator

(Lit when the batch count value is displayed.)

7. Present Value (Main Display)

(Character height: 10 mm, white

Displayed only when the configuration

selection mode is not tachometer mode.

15. Key-protect Switch

Note: The reset functions depends on the selected configuration.

Configuration

Reset operation

1-stage/2-stage

preset counter

Resets the present value and outputs.

Total and preset

counter

• Resets the present value and outputs.

• When the total count value is displayed, resets the present value, the total count

value, and outputs.

Batch counter

• Resets the present value and OUT2.

• When the batch count value is displayed, resets the present value, the batch count

value, and outputs.

Dual counter

Resets the CP1 present value, CP2 present value, dual count value, and outputs.

Twin counter

Resets the CP1 present value and output 1 when the CP1 present value is displayed.

Resets the CP2 present value and output 2 when the CP2 present value is displayed.

Tachometer

Holds the measurement value and outputs (hold function).

(When the input mode is 2-input independent measurement, the CP1 measurement

value display will hold the CP1 measurement value and output 1 and the CP2

measurement value display will hold the CP2 measurement value and output 2.)

Model with 6 Digits

10 mm

6 mm

Character Size

for Sub-display

Character Size

for Main Display

H7CC-R11W 数据表(PDF) 10 Page - Omron Electronics LLC

H7CC-R11W 数据表(HTML) 10 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

数据表下载