H7CC-R11W datasheet(31/66 Pages) OMRON

31 / 66 page

H7CC-A

tachometer

Setting Procedure Guide

Tachometer Operation

Step1

The H7CC-AW

@/AU@ is a Counter that contains more than one functional counter.

At the time of delivery

*, the H7CC is set to the 1-stage preset counter configuration

or 2-stage preset counter configuration.

Enter configuration selection mode using the following chart and

set the tachometer mode.

twn

(1-stage

preset

counter)

(2-stage

preset

counter)

(Total and

preset counter)

(Batch

counter)

(Dual

counter)

(Twin

counter)

(Tachometer)

Select the function using the UP1 Key (DW1 Key) .

UP1+UP6 or DW1+DW6

(Press and hold for 2 s)

UP1+UP6 or DW1+DW6

(Press and hold for 2 s)

Run mode

Power ON

Configuration

selection mode

Model

Default mode

H7CC-AW

H7CC-AU

2-stage preset

counter

1-stage preset

counter

* Table Default Modes and Selectable Functions

Any mode

Selectable mode

UP1+UP3 or DW1+DW3

(Press and hold for 2 s)

UP1+UP3 or DW1+DW3

(Press and hold for 2 s)

Run mode

Power ON

Function

setting mode

* Use UP1+UP3 to move up and

DW1+DW3 to move down

Step2

(99.999)

(1.000)

(0.001)

From

(30 Hz)

(10 kHz)

(LO)

(HI)

(LO)

(HI)

(No decimal point) (One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

(Four digits after

decimal point)

Prescale value

(PSCL)

Parameters are set with the operation keys on the front panel.

Change to Function Setting Mode.

The characters displayed in reverse video are the default settings.

In the function setting mode, the status indicator of the keys that can be set lights up.

(Example) In the case of the prescale value (PSCL)

A value from 0.001 to 99.999 can be set, and therefore, the status indicator

of the UP1 Key to UP5 Key (DW1 Key to DW5 Key) lights up.

hilo

30hz

area

hihi

lolo

--.----

0.001

99.999

1.000

(AREA)

(HI-HI)

(LO-LO)

(HI-LO)

(Error) (Absolute ratio)

(1 input) (2 inputs)

(Error ratio)

Counting

speed

(CNTS)

Tachometer

output mode

(TOTM)

Decimal point

position

(DP)

Tachometer

input mode

(TINM)

• Set the tachometer input mode using the UP1 Key (DW1 Key).

• Set the tachometer output mode using the UP1 Key (DW1 Key).

• Set the counting speed using the UP1 Key (DW1 Key).

Note: Even if 10 kHz is selected when the tachometer input mode is F2 to F5, the counting speed will be 5 kHz.

Note: The indicator display is disabled during the upper or lower limit setting.

*1 Set tachometer output modes 1 and 2

using the UP1 Key (DW1 Key).

Tachometer

output

mode 1

(TO1M)

Note: Displayed only when the tachometer

input mode is F2 (2 inputs).

Tachometer

output

mode 2

(TO2M)

• Set the decimal point position using the UP1 Key (DW1 Key).

Note: “--.----“ will be displayed when pulse width measurement is set or when the display unit is set to seconds.

*1 If the mode is switched to the function setting mode during operation, operation will continue.

*2 Changes made to settings in function setting mode are enabled for the first time when the mode is changed to run mode.

Also, when settings are changed, the counter is reset (present value initialized and output turned OFF) on returning to run mode.

1000

pscl

For details on operations and display in run mode, refer to page 37.

H7CC-R11W 数据表(PDF) 31 Page - Omron Electronics LLC

H7CC-R11W 数据表(HTML) 31 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

数据表下载

链接网址

H7CC-R11W 数据表(PDF) 31 Page - Omron Electronics LLC

H7CC-R11W 数据表(HTML) 31 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

数据表 下载

链接网址

数据表下载