TSOP772..W, TSOP774..W

www.vishay.com

Vishay Semiconductors

Datasheet Values Refer to PCN-OPT-1224-2022

Rev. 2.2, 19-Aug-2022

3

Document Number: 82466

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

Fig. 1 - Output Active Low

Fig. 2 - Pulse Length and Sensitivity in Dark Ambient

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage

VS

-0.3 to +6

V

Supply current

IS

5mA

Output voltage

VO

-0.3 to 5.5

V

Voltage at output to supply

VS - VO

-0.3 to (VS + 0.3)

V

Output current

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

Soldering temperature

t

≤ 10 s, 1 mm from case

Tsd

260

°C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply voltage

VS

2.0

-

5.5

V

Supply current

VS = 3.3 V, Ev = 0

ISD

0.25

0.35

0.45

mA

Ev = 40 klx, sunlight

ISH

-0.8

-

mA

Transmission distance

Ev = 0, IR diode TSAL6200, IF = 50 mA,

test signal see Fig. 1

d-

12

-

m

Output voltage low

IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Test signal: RC5 code

Ee min.

-0.4

0.8

mW/m2

Test signal: NEC code

Ee min.

-0.6

1.0

mW/m2

Maximum irradiance

tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1

Ee max.

50

-

-

W/m2

Directivity

Angle of half transmission distance

ϕ1/2

-± 75

-

°

E

e

T

t

pi

(1)

t

V

O

V

OH

V

OL

t

Optical Test Signal

(IR diode TSAL6200, 30 pulses, f = f

0, T = 10 ms)

Output Signal

t

d

(2)

t

po

(3)

(2) 7/f

0 < td < 13/f0

(3) t

pi - 4/f0 < tpo < tpi + 4/f0

16110-12

(1) t

pi ≥ 10/f0

10

100

1000

10000

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

0.1

10

1000

100 000

Axis Title

E

e - Irradiance (mW/m

2)

Output pulse width

Input burst length

λ= 950 nm,

optical test signal, Fig. 1