TSOP931..DF1P, TSOP933..DF1P, TSOP935..DF1P

www.vishay.com

Vishay Semiconductors

Rev. 1.1, 05-Aug-2021

2

Document Number: 82883

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• 30 kHz and 33 kHz only available on written request

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

PARTS TABLE

AGC

LEGACY, FOR SHORT BURSTS

(AGC1)

ENHANCED NOISE

SUPPRESSION (AGC3)

MAXIMIZED NOISE

SUPPRESSION (AGC5)

Carrier frequency

30 kHz

TSOP93130DF1P

TSOP93330DF1P

TSOP93530DF1P

33 kHz

TSOP93133DF1P

TSOP93333DF1P

TSOP93533DF1P

36 kHz

TSOP93136DF1P

TSOP93336DF1P (1)(5)

TSOP93536DF1P

38 kHz

TSOP93138DF1P

TSOP93338DF1P (2)(4)

TSOP93538DF1P

40 kHz

TSOP93140DF1P

TSOP93340DF1P

TSOP93540DF1P

56 kHz

TSOP93156DF1P

TSOP93356DF1P

TSOP93556DF1P (3)

Package

Minimold

Pinning

1 = OUT, 2 = GND, 3 = VS

Dimensions (mm)

5.4 W x 6.35 H x 4.9 D

Mounting

SMD

Application

Remote control

Best choice for

(1) RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2 (5) MCIR

Special options

• Narrow optical filter: www.vishay.com/doc?81590

• Wide optical flter: www.vishay.com/doc?82726

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage

VS

-0.3 to +3.6

V

Supply current

IS

3mA

Output voltage

VO

-0.3 to (VS + 0.3)

V

Output current

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

Soldering temperature

t

≤ 10 s, 1 mm from case

Tsd

260

°C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply current

Ev = 0, VS = 3.3 V

ISD

0.25

0.37

0.45

mA

Ev = 40 klx, sunlight

ISH

-0.50

-

mA

Supply voltage

VS

2.0

-

3.6

V

Transmission distance

Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA

d-

28

-

m

Output voltage low

IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Test signal: XMP code

Ee min.

-

0.12

0.25

mW/m2

Test signal: NEC code

-

0.09

0.20

Maximum irradiance

tpi - 3.0/f0 < tpo < tpi + 3.5/f0,

test signal see Fig. 1

Ee max.

30

-

-

W/m2

Directivity

Angle of half transmission

distance

ϕ1/2

-± 45

-

°