LMP7701_06 datasheet(6/22 Pages) NSC

6 / 22 page

±5V Electrical Characteristics (Note 4) (Continued)

Unless otherwise specified, all limits are guaranteed for T

A = 25˚C, V

+ = 5V, V− = −5V, V

CM = 0V, and RL > 10 k

Ω to 0V.

Boldface limits apply at the temperature extremes.

Symbol

Parameter

Conditions

Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

Output Swing High

L =2k

Ω to 0V

LMP7701

150

170

from V

L =2k

Ω to 0V

LMP7702/LMP7704

180

290

L =10k

Ω to 0V

LMP7701

100

L =10k

Ω to 0V

LMP7702/LMP7704

150

Output Swing Low

L =2k

Ω to 0V

LMP7701

130

150

from V

–

L =2k

Ω to 0V

LMP7702/LMP7704

180

290

L =10k

Ω to 0V

LMP7701

L =10k

Ω to 0V

LMP7702/LMP7704

110

Output Short Circuit Current

(Notes 3, 9)

Sourcing V

O =0V

IN = 100 mV (LMP7701)

Sourcing V

O =0V

IN = 100 mV

(LMP7702/LMP7704)

Sinking V

O =0V

IN = −100 mV

Supply Current

LMP7701

0.790

1.1

1.3

LMP7702

1.7

2.1

2.5

LMP7704

3.2

4.2

5.0

Slew Rate (Note 10)

V = +1, VO =9VPP

10% to 90%

1.1

V/µs

GBW

Gain Bandwidth Product

2.5

MHz

THD+N

Total Harmonic Distortion + Noise

f = 1 kHz, A

V =1,RL =10k

Ω

0.02

Input-Referred Voltage Noise

f = 1 kHz

nV/

Input-Referred Current Noise

f = 100 kHz

fA/

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics Tables.

Note 2: Human Body Model is 1.5 k

Ω in series with 100 pF. Machine Model is 0Ω in series with 200 pF.

Note 3: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is

PD =(TJ(MAX) -TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.

Note 4: Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of

the device.

Note 5: Typical values represent the parametric norm at the time of characterization.

Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality

Control (SQC) method.

Note 7: Guaranteed by design.

Note 8: Positive current corresponds to current flowing into the device.

Note 9: The short circuit test is a momentary test.

Note 10: The number specified is the slower of positive and negative slew rates.

LMP7701 数据表(PDF) 6 Page - National Semiconductor (TI)

LMP7701 数据表(HTML) 6 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

数据表下载

链接网址

LMP7701 数据表(PDF) 6 Page - National Semiconductor (TI)

LMP7701 数据表(HTML) 6 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

数据表 下载

链接网址

数据表下载